MAGRES EAM580R-SC - Analog | Encoder assoluti

Encoder single- or multiturn / Analog
E1 compliant design
High protection up to IP 67
High resistance to shock and vibrations
Protection against corrosion CX (C5-M)
Wire cross section 0.5 mm²
Teach input for adjustment of measuring range
Applicable up to PLd (ISO 13849)

disponibilità su richiesta

Dati tecnici

mostra tutti

Dati tecnici - Valori elettrici

Tensione operativa

8...30 VDC
14...30 VDC

Reverse polarity protection

Tip. corrente operativa

20 mA (24 VDC, w/o load)

Initializing time

≤ 170 ms after power on

Response time

< 1 ms

Interface

Analog 0...10 V / 0.5...4.5 V / 4...20 mA / Resolution: 12 bit

Function

Multiturn
Singleturn

Teach range

5°...359.9° (singleturn)
5°...32767 turns (multiturn)

Absolute accuracy

±0,15 ° (+20 ±15 °C)
±0,25 ° (-40...+85 °C) sensor

Accuracy analog output

±0.5 % of whole measuring range
(-40...+85 °C)

Principio di scansione

Magnetic

Immunità alle interferenze

EN 61000-6-2
ISO 11452-2:2004* / -5:2002*
ISO 7637-2:2004*
ISO 10605:2008 + Amd 1:2014 (CD ±8 kV / AD ±15 kV)
* Severity level according to ECE R10 (Rev. 4)

Emissione di interferenze

EN 61000-6-4
CISPR 25:2008 (30...1000 MHz)
ISO 7637-2:2004*
* Severity level according to ECE R10 (Rev. 4)

MTTF_d (ISO 13849)

High (>100 years)
Use in safety functions exclusively based on Application Note and MTTFd reliability prediction (request separately).

Programmable parameters

Measuring range teachable

Diagnostic function

DATAVALID

Factory setting

360° and 10 revolutions (other on request)

Approvazione

UL approval / E217823

Dati tecnici - progettazione meccanica

Grandezza (flangia)

ø58 mm

Tipo di albero

ø10 x 20 mm, solid shaft with flat

Flangia

Clamping flange

Classe di protezione EN 60529

IP 67 (with shaft seal)

Velocità operativa

≤6000 rpm

Coppia di spunto

≤2,5 Ncm (+20 °C, IP 67)

Moment of inertia

15,38 gcm²

Carico dell‘albero massimo ammesso

≤40 N assiale
≤80 N radiale

Materiale

Housing: steel, powder-coated
Flange: aluminium
Albero: acciaio inox

Corrosion protection

IEC 60068-2-52 Salt mist
for ambient conditions CX (C5-M) according to ISO 12944-2

Temperatura operativa

-40...+85 °C (see general informations)

Relative humidity

95 %

Resistenza

EN 60068-2-6
Vibrazione 30 g, 10-2000 Hz
EN 60068-2-27
Urti 500 g, 1 ms

Peso ca.

250 g

Allacciamento

Flange connector M12, 5-pin
Cable 2 m

Scaricare

mostra tutti

Data sheet

Schede tecniche – EAM580R-SC - Analog
- ZH (pdf | 1 MB)
Schede tecniche – EAM580R-SC - Analog
- FR (pdf | 947 KB)
Schede tecniche – EAM580R-SC - Analog
- DE (pdf | 918 KB)
Schede tecniche – EAM580R-SC - Analog
- EN (pdf | 945 KB)

Quickstart

EAM580R - analog
- DE/EN/FR/IT/ES (pdf | 860 KB)

Brochures / Catalogs

Brochure – Magnetic absolute encoders EAM580 / EAM360
- DE (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- EN (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- FR (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- IT (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- ES (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- ZH (pdf | 1 MB)

Declaration of conformity

DoC / CoC - EAM580 / EAM580R
- DE/EN/FR (pdf | 281 KB)

CAD

EAM580 / EAM580R: Solid shaft ø10 mm, cable radial, clamping flange, IP67
- STEP (zip | 200 KB)
EAM580 / EAM580R: Solid shaft ø10 mm, M12 radial, clamping flange, IP67
- STEP (zip | 190 KB)

Accessori

mostra tutti

Accessori di montaggio

	Double loops coupling (D1=10 / D2=10) For encoder with solid shaft Articolo n..: 11101781	Thermally and electrically isolated Absorbing shocks and vibration Excellent compensation of radial, lateral and angular misalignments Medium torsional stiffness Low restoring forces Maintenance-free
	Bellows coupling (D1=06 / D2=10) For encoder with solid shaft Articolo n..: 11050507	Backlash-free angle-synchronous transmission Optimum compensation of misalignments Very high torsional spring stiffness Small restoring force Vibration damping Stainless steel bellows
	Coupling CPS25 (L=19, D1=10 / D2=10) For encoder with solid shaft Articolo n..: 11065923	Precision coupling Torsionally stiff coupling with low installation depth Pluggable Electrically insulating center disk Suitable for very high speeds
	Coupling CPS25 (L=19, D1=10 / D2=06) For encoder with solid shaft Articolo n..: 11065922	Precision coupling Torsionally stiff coupling with low installation depth Pluggable Electrically insulating center disk Suitable for very high speeds
	Spring washer coupling (D1=6 / D2=10) For encoder with solid shaft Articolo n..: 10141132	Backlash-free and angle-synchronous transmission of rotary movements Plug-in version Electric isolated Suitable for very high speeds Good compensation of all misalignments
	Spring washer coupling (D1=10 / D2=10) For encoder with solid shaft Articolo n..: 10141133	Backlash-free and angle-synchronous transmission of rotary movements Plug-in version Electric isolated Suitable for very high speeds Good compensation of all misalignments
	Coupling CPS37 (L=24, D1=10 / D2=06) For encoder with solid shaft Articolo n..: 11069337	Precision coupling Torsionally stiff coupling with low installation depth Pluggable Electrically insulating center disk Suitable for very high speeds
	Coupling CPS37 (L=24, D1=10 / D2=10) For encoder with solid shaft Articolo n..: 11069340	Precision coupling Torsionally stiff coupling with low installation depth Pluggable Electrically insulating center disk Suitable for very high speeds
	Bellows coupling (D1=10 / D2=10) For encoder with solid shaft Articolo n..: 11053277	Backlash-free angle-synchronous transmission Optimum compensation of misalignments Very high torsional spring stiffness Small restoring force Vibration damping Stainless steel bellows
	Spring encoder arm Articolo n..: 11101893	Tether arm for Ø58 mm with clamping flange Optimal for use encoders with measuring wheel Virtually any contact pressure adjustable Versatile mounting options
	Mounting adaptor For encoders with clamping flange Articolo n..: 10125051	Glass-fiber reinforced plastic Excellent resistance against temperature and chemicals Electrically isolated encoder mount

Connettori e cavi

	Female connector M12, 5-pin, straight, without cable Articolo n..: 10153968	Female connector M12, 5-pin, straight
	ESG 34CP0200G Articolo n..: 11229672	M12, female, A-coded; 5-poles; PUR, 200 cm, shielded, free cable end Dragchain capable Head A: IP65, IP66K, IP67 Cable: Good resistance against chemicals, flames and oils Halogen free
	ESG 34CP0500G Articolo n..: 11229675	M12, female, A-coded; 5-poles; PUR, 500 cm, shielded, free cable end Dragchain capable Head A: IP65, IP66K, IP67 Cable: Good resistance against chemicals, flames and oils Halogen free
	ESG 34CP1000G Articolo n..: 11224777	M12, female, A-coded; 5-poles; PUR, 1000 cm, shielded, free cable end Dragchain capable Head A: IP65, IP66K, IP67 Cable: Good resistance against chemicals, flames and oils Halogen free

Measuring wheels

	MR752.10A Small measuring wheel Articolo n..: 11011440	Circumference 30.48 cm Surface profile: Smooth Surface material: Polyurethan Bore ø10 mm
	MR241.10D Small measuring wheel Articolo n..: 11033281	Circumference 20 cm Surface profile: Smooth Surface material: Hytrel TPE-E Bore ø10 mm
	MR261.10A Small measuring wheel Articolo n..: 11033290	Circumference 20 cm Surface profile: Knopped rubber Surface material: Nitrile NBR Bore ø10 mm
	MR291.10D Small measuring wheel Articolo n..: 11033300	Circumference 20 cm Surface profile: Knurled Surface material: Hytrel TPE-E Bore ø10 mm
	MR512.10A Large measuring wheel Articolo n..: 11033308	Circumference 50 cm Surface profile: Cross-knurled Surface material: Aluminium Bore ø10 mm
	MR552.10A Large measuring wheel Articolo n..: 11033323	Circumference 50 cm Surface profile: Smooth Surface material: Polyurethan Bore ø10 mm
	MR562.10A Large measuring wheel Articolo n..: 11033329	Circumference 50 cm Surface profile: Knopped rubber Surface material: Nitrile NBR Bore ø10 mm
	MR542.10D Large measuring wheel Articolo n..: 11038480	Circumference 50 cm Surface profile: Smooth Surface material: Hytrel TPE-E Bore ø10 mm
	MR592.10D Large measuring wheel Articolo n..: 11038481	Circumference 50 cm Surface profile: Knurled Surface material: Hytrel TPE-E Bore ø10 mm