2. Panoramica dei prodotti
  3. Encoder / sensori angolari
  4. Encoder incrementale HeavyDuty
  5. Gamma completa ad albero cavo e passante
  6. HMG10-B - Incremental
Dati tecnici
Dati tecnici - Valori elettrici
Tensione operativa
  • 4.75...30 VDC
Short-circuit proof
  • Yes
Corrente operativa senza carico
  • ≤100 mA
Initializing time
  • ≤ 500 ms after power on
Impulsi per giro
  • 1 … 131072
Sfasamento
  • 90 ° ±20°
Rapporto ciclico
  • 40…60 %
Segnale di riferimento
  • Impulso zero, ampiezza 90°
Principio di scansione
  • Magnetic
Segnale di uscita
  • A+, B+, R+, A-, B-, R-
  • Error output nE+, nE-
Livelli di uscita
  • TTL/HTL (Vin = Vout)
Programming interface
  • RS485 (≤600 m)
Programmable parameters
  • Pulse number
  • Switch-off and switch-on speeds
  • Switching delay time
Diagnostic function
  • Function control
Status indicator
  • 4 LEDs in device back side
Immunità alle interferenze
  • EN 61000-6-2
Emissione di interferenze
  • EN 61000-6-3
Approvazione
  • CE
  • UL approval / E217823
Dati tecnici - Valori nominali elettrici (variatori di velocità)
Switching accuracy
  • ± 2 % (or 1 Digit)
Switching outputs
  • 1 output (Open collector)
Output switching capacity
  • 30 VDC; ≤100 mA
Switching hysteresis
  • 10 … 100 % adjustable
Switching delay time
  • ≤20 ms
Dati tecnici - progettazione meccanica
Grandezza (flangia)
  • ø105 mm
Tipo di albero
  • ø16...20 mm (blind hollow shaft)
  • ø17 mm (cone shaft 1:10)
Carico dell‘albero massimo ammesso
  • ≤450 N assiale
  • ≤650 N radiale
Flangia
  • Support plate for torque arm, 360° freely positionable
Classe di protezione EN 60529
  • IP 66 / IP 67
Velocità operativa
  • ≤12000 rpm
Range of switching speed
  • ns (off) = ±2...12000 rpm, factory setting 6000 rpm
Tip. coppia operativa
  • 10 Ncm
Rotore momento d‘inerzia
  • 950 gcm²
Materiale
  • Housing: aluminium alloy
  • Albero: acciaio inox
Temperatura operativa
  • -40...+95 °C
Relative humidity
  • 95 % non-condensing
Resistenza
  • IEC 60068-2-6
  • Vibrazione 30 g, 10-2000 Hz
  • IEC 60068-2-27
  • Urti 400 g, 1 ms
Corrosion protection
  • IEC 60068-2-52 Salt mist
  • for ambient conditions CX (C5-M) according to ISO 12944-2
Allacciamento
  • Terminal box
  • Flange connector M23
Peso ca.
  • 1,6 kg
Scaricare
Data sheet
Operating Manual
Declaration of conformity

Accessori
Accessori di montaggio
The selected altAttribute does not exist! Torque arm M6, length 67...70 mm

Articolo n..: 11043628
  • Torque arm for hollow shaft encoder
  • Swivel joints size M6 according to DIN ISO 12240-4, size series K
  • Compensate for mounting tolerances of the drive shaft in an axial direction
  • Standard version
  • Length 67...70 mm
The selected altAttribute does not exist! Torque arm M6, length 120...130 mm (≥71 mm)

Articolo n..: 11004078
  • Torque arm for hollow shaft encoder
  • Swivel joints size M6 according to DIN ISO 12240-4, size series K
  • Compensate for mounting tolerances of the drive shaft in an axial direction
  • Standard version
  • Length 120...130 mm
  • Can be shortened to ≥71 mm
The selected altAttribute does not exist! Torque arm M6, length 425...460 mm (≥131 mm)

Articolo n..: 11002915
  • Torque arm for hollow shaft encoder
  • Swivel joints size M6 according to DIN ISO 12240-4, size series K
  • Compensate for mounting tolerances of the drive shaft in an axial direction
  • Standard version
  • Length 425...460 mm
  • Can be shortened to ≥131 mm
The selected altAttribute does not exist! Torque arm M6 insulated, length 67...70 mm

Articolo n..: 11054917
  • Torque arm for hollow shaft encoder
  • Swivel joints size M6 according to DIN ISO 12240-4, size series K
  • Compensate for mounting tolerances of the drive shaft in an axial direction
  • Insulated version
  • Length 67...70 mm
The selected altAttribute does not exist! Torque arm M6 insulated, length 120...130 mm (≥71 mm)

Articolo n..: 11072795
  • Torque arm for hollow shaft encoder
  • Swivel joints size M6 according to DIN ISO 12240-4, size series K
  • Compensate for mounting tolerances of the drive shaft in an axial direction
  • Insulated version
  • Length 120...130 mm
  • Can be shortened to ≥71 mm
The selected altAttribute does not exist! Torque arm M6 insulated, length 425...460 mm (≥131 mm)

Articolo n..: 11082677
  • Torque arm for hollow shaft encoder
  • Swivel joints size M6 according to DIN ISO 12240-4, size series K
  • Compensate for mounting tolerances of the drive shaft in an axial direction
  • Insulated version
  • Length 425...460 mm
  • Can be shortened to ≥131 mm
The selected altAttribute does not exist! Mounting kit for torque arm size M6 and earthing strap

Articolo n..: 11077197

Mounting kit for fixing a torque arm size M6 and an earthing strap.
The selected altAttribute does not exist! Mounting and dismounting set

Articolo n..: 11077087

Mounting and dismounting set for fixing a blind hollow shaft encoder to the drive shaft and for dismounting the encoder from the drive shaft.
Connettori e cavi
The selected altAttribute does not exist! Sensor cable for encoders HEK 8

The sensor cable HEK 8 is a proven industrial product designed to match high demands. It is halogen free and its rugged outer construction allows it to be pulled and dragged in free conditions. It is certified to UL 20233. The cable can be supplied in any length and pre-fitted with various connectors.
The selected altAttribute does not exist! Sensor cable for encoders HEK 17

The sensor cable HEK 17 is a proven industrial product designed to match high demands. It is halogen free, oil-resistant, abrasion and notch-resistant and its rugged outer construction allows it to be pulled and dragged in free conditions. It is certified to UL AWM Style 20236, CSA AWM IA/B; IIA/B FT 1, UL File No. E63634. The cable can be supplied in any length and pre-fitted with various connectors.
The selected altAttribute does not exist! Programming cable for HMG10P/PMG10P (SSI) with terminal box

Articolo n..: 11191144
  • Adapter cable for programming the HMG10P/PMG10P SSI series with terminal box
  • With D-SUB connector (male) for connection of encoders of HMG10/PMG10 SSI series with terminal box to the WLAN adapter Z-PA.SDL.1
  • The encoder can be conntected to the WLAN adapter in ONLINE or OFFLINE mode
Programmazione accessori
The selected altAttribute does not exist! Z-PA.SDL.1 - WLAN-Adapter

Articolo n..: 11190106
  • Programming unit for HMG10P/PMG10P series
  • Parametrization of SSI absolute signal, incremental output and speed switch (depending on encoder version)
  • Monitoring of current position, speed und temperature
  • Connection over Ethernet or wireless over WLAN
  • Simple and intuitive use via webbrowser on pc, tablet or smartphone
  • Fast parameter download
In alto