2. GA240 - parallel
Dati tecnici
Dati tecnici - Valori elettrici
Tensione operativa
  • 10...30 VDC
Reverse polarity protection
  • Yes
Corrente operativa senza carico
  • ≤60 mA (24 VDC)
Initializing time typ.
  • 20 ms after power on
Interface
  • 13 parallel outputs
Function
  • Singleturn
Steps per revolution
  • 8192 / 13 bit
Absolute accuracy
  • ±0,025 °
Principio di scansione
  • Ottico
Code
  • Gray or binary
Code sequence
  • CW/CCW coded by connection
Inputs
  • Control signals UP/DOWN inv. and zero
  • STORE inv.
  • ENABLE inv.
Livelli di uscita
  • Push-pull short-circuit proof
Immunità alle interferenze
  • EN 61000-6-2
Emissione di interferenze
  • EN 61000-6-4
Diagnostic function
  • Self-diagnosis
  • Code continuity check
Approvazione
  • UL approval / E63076
Dati tecnici - progettazione meccanica
Grandezza (flangia)
  • ø58 mm
Tipo di albero
  • ø10 mm solid shaft
Flangia
  • Clamping flange
Classe di protezione EN 60529
  • IP 54 (without shaft seal)
  • IP 65 (with shaft seal)
Velocità operativa
  • ≤10000 giri/min (meccanico)
  • ≤6000 rpm (electric)
Coppia di spunto
  • ≤0,015 Nm (+25 °C, IP 54)
  • ≤0,03 Nm (+25 °C, IP 65)
Rotore momento d‘inerzia
  • 14,5 gcm²
Carico dell‘albero massimo ammesso
  • ≤20 N assiale
  • ≤40 N radiale
Materiale
  • Housing: aluminium
  • Flange: aluminium
Temperatura operativa
  • -25...+85 °C
  • -40...+85 °C (optional)
Relative humidity
  • 95 % non-condensing
Resistenza
  • EN 60068-2-6
  • Vibrazione 10 g, 16-2000 Hz
  • EN 60068-2-27
  • Urti 200 g, 6 ms
Peso ca.
  • 250 g
Allacciamento
  • Connector M27, 21-pin
  • Cable 1 m
Scaricare
Data sheet
Quickstart
Certificates / approvals
Declaration of conformity

Disegni
Drawings
The selected altAttribute does not exist!

(png | 82 KB)
Accessori
Accessori di montaggio
The selected altAttribute does not exist! Set of eccentric fixings type A

Articolo n..: 11065545
  • With 3 eccentric fixings type A
The selected altAttribute does not exist! Adaptor plate for clamping flange to convert into synchro flange

Articolo n..: 10141255
  • Adaptor plate for encoder with clamping flange for modification into synchro flange
The selected altAttribute does not exist! Mounting adaptor
For encoders with clamping flange

Articolo n..: 10125051
  • Glass-fiber reinforced plastic
  • Excellent resistance against temperature and chemicals
  • Electrically isolated encoder mount
The selected altAttribute does not exist! Adaptor plate for clamping flange, mounting by eccentric fixings (order separately) (Z 119.025)

Articolo n..: 11034088
  • Adaptor plate for clamping flange with 3x screws
The selected altAttribute does not exist! Spring washer coupling (D1=6 / D2=10)
For encoder with solid shaft

Articolo n..: 10141132
  • Backlash-free and angle-synchronous transmission of rotary movements
  • Plug-in version
  • Electric isolated
  • Suitable for very high speeds
  • Good compensation of all misalignments
Connettori e cavi
The selected altAttribute does not exist! Female connector M27, 21-pin, without cable (Z 132.001)

Articolo n..: 11034174
  • Female connector M27 with screwable nut
  • With or without cable (shielded) in different lengths
  • Cable version: shield is placed onto the connector housing
The selected altAttribute does not exist! Female connector M27, 21-pin, 2 m cable (Z 132.003)

Articolo n..: 11034175
  • Female connector M27 with screwable nut
  • With or without cable (shielded) in different lengths
  • Cable version: shield is placed onto the connector housing
The selected altAttribute does not exist! Female connector M27, 21-pin, 5 m cable (Z 132.005)

Articolo n..: 11034176
  • Female connector M27 with screwable nut
  • With or without cable (shielded) in different lengths
  • Cable version: shield is placed onto the connector housing
The selected altAttribute does not exist! Female connector M27, 21-pin, 10 m cable (Z 132.007)

Articolo n..: 11034177
  • Female connector M27 with screwable nut
  • With or without cable (shielded) in different lengths
  • Cable version: shield is placed onto the connector housing
In alto