VCXG-32C.I.XT

Artigo nº: 11188951

2048 x 1536 px
Sony IMX265
1/1.8" CMOS
39 fps
Gigabit Ethernet

Não mais disponível

Temos o prazer de ajudá-lo na seleção de alternativas

Dados técnicos

mostrar tudo

informação do sensor

Sensor

Sony IMX265 Gen2

Mono/Color

Color

Sensor type

1/1.8″ CMOS

Shutter type

Global shutter

Resolution

2048 × 1536 px

Pixel size

3.45 × 3.45 µm

Exposure time

0,001 … 60000 ms

Dark noise

1,97 e-

Saturation capacity

8252 e-

Dynamic range

70,9 dB

Signal-to-noise ratio

39,7 dB

Quantum efficiency

45,9 % @ 465 nm
57,2 % @ 536 nm
52,8 % @ 631 nm

formatos de aquisição

Image formats, interface frame rate max.

Full Frame, 2048 × 1536 px, max. 39 fps
Binning 2×2, 1024 × 768 px, max. 56 fps
Binning 2×1, 1024 × 1536 px, max. 56 fps
Binning 1×2, 2048 × 768 px, max. 56 fps

Image formats, aquisition frame rate max. (Burst Mode)

Full Frame, 2048 × 1536 px, max. 56 fps

Pixel formats

BayerRG8
BayerRG10
BayerRG12
BayerRG12 Packed
Mono8
Mono10
Mono12
Mono12 Packed
RGB8
BGR8

Analog controls

Gain (0 … 48 dB)
Offset (0 … 255 LSB 12 Bit)

Color models

Mono
RGB
BGR

características da câmera

Basic Functions

Exposure
Gain / Color Gain
Trigger / Exposure Active (Flash)
Binning 2x2
Partial Scan
Offset
Free Running Mode (Live Image)

Auto Functions

Exposure Auto
Gain Auto
White Balance Auto
Color Transformation Auto

Image Pre-processing

Image Flipping (X/Y)
Color Processing (RGB, BGR, Mono)
Color Enhancement (with optimized ColorTransformationMatrix)
LUT / Gamma

Acquisition / Interface

Burst Mode
Adjustable Framerate
Short Exposure Time Enable
Device Link Throughput Limit
Internal Image Buffer

Synchronization

free running
trigger

Trigger sources

Hardware
Software
ActionCommand

Trigger delay

0 … 2 s, tracking and buffering of up to 256 trigger signals

Process Synchronization

Events
Timer
Trigger Delay
Debouncer
Counter
Sequencer
Trigger via Action CMD (GigE)
Additional Output Modes (e.g. Trigger Ready)
PWM (PWM Duration / PWM Duty Cycle)
4 power outputs with up to 120 W (max. 48 V / 2.5 A)
Selectable Output format (e.g. Tri State, Push Pull)
Chunk data inside transferred image
Encoder support via Counter End trigger source

Additional Functions

User Set
Integrated temperature sensor
Readable additional information (e.g. sensor information)
Save Custom Data

Internal image buffer

72 MB
8 images (Trigger Mode)
1 image (Free Running Mode)

interfaces e conectores

Data interface

Gigabit Ethernet, Transfer rate 1000 Mbits/sec, Fast Ethernet, Transfer rate 100 Mbits/sec, Connector: M12 / 8 pol x-coded, screwable type

Process interface

M12 / 12 pins a-coded (SACC-CI-M12MS-12CON-L180)

Power supply

via M12/12 pins a-coded or Power over Ethernet (PoE)

Dados mecânicos

Lens mount

C-mount

Width

40 mm

Height

40 mm

Depth

50,8 mm

Weight

≤ 137 g

Material

aluminum, hard-anodized

Dados Elétricos

Voltage supply range +Vs

12 … 24 V DC (external power supply)
36 … 57 V DC (Power over Ethernet)

Power consumption

Approx. 2.4 W @ 12 VDC and 39 fps
Approx. 3.1 W @ 48 VDC (PoE) and 39 fps

Flash memory size

128 kB

Condições ambientais

Operating temperature

-40 ... +70 °C @ T = measurement point

Storage temperature

-40 … +70 °C

Humidity

10 … 90 % (non-condensing)

Protection class

IP 54 (with mounted lens and cable)
IP 65 (with mounted tube and cable)
IP 67 (with mounted tube and cable)
IP 69K (with stainless steel housing accessory)

entradas/saídas digitais

Lines

4 input lines
4 power output lines with pulse width modulation (PWM) (max. 48 V / max. 2,5 A)

Conformity

CE
RoHS
UL recognized
KC (R-R-BkR-VCXG-51MI)
EAC

Software

mostrar tudo

Software packages

Baumer neoAPI (Windows, Linux, Linux ARM)
- Link
Baumer Camera Explorer (Windows, Linux, Linux ARM)
- Link
Baumer GAPI SDK v2.x (Windows, Linux, Linux ARM)
- Link
Baumer GAPI software examples
- Link
Third Party Software
- Link

Software

Baumer IPConfig Tool v2.0.2 (Windows)
- EN (zip | 5 MB)

Transferências

mostrar tudo

Data sheet

Data sheet – VCXG-32C.I.XT
- DE (pdf | 1 MB)
Data sheet – VCXG-32C.I.XT
- EN (pdf | 1 MB)
Detailed data sheet – xxx
- EN (pdf | 578 KB)

Quickstart

Quick Start Guide VCXG.I
- EN (pdf | 1 MB)

Operating Manual

User’s Guide VCXG / VCXG.I / VCXU cameras
- EN (pdf | 11 MB)

Certificates / approvals

CE certification
- Download (pdf | 280 KB)
UL certification
- EN (pdf | 506 KB)
KC registration
- KO/EN (pdf | 692 KB)

Additional information

EMVA 1288 Summary Sheet
- EN (pdf | 286 KB)
Compliant list for Baumer industrial cameras (GigE)
- EN (pdf | 882 KB)

Application notes

Application Notes
- Link

CAD

VCXG-32C.I .XT / STEP
- Download (zip | 593 KB)

EPLAN

Link para o portal de dados
- Link para o portal de dados

Desenhos

mostrar tudo

Dimension drawing

The selected altAttribute does not exist!

(png | 119 KB)

Schematic diagram

(png | 379 KB)

(png | 252 KB)

(png | 159 KB)

Acessórios

mostrar tudo

Power supply

Power Supply 24V/1.0A Int. DC Connector

Artigo nº: 11079750

power supply 24V/1,0A with adapters for EU, US, UK AU, KR
in combination with "Cable power adapter M12/DC connector" (11048083) suitable for VCXG.I(.XT), VLXT, VAX and VeriSens

Starter Kit

VCXG.I Starter Kit

Artigo nº: 11190348

GigE PCIe interface board
GigE cable 5,0 m (M12/x-coded)
Power Supply 24 V/1.0 A with adapter cable M12/12-pin to DC connector
Mounting Adapter Type B (Tripod)
Tube system M47 with adapter (11185373) and tube (11185370)
camera not included
available

PCIe/Adapter

	PCIe Ethernet Server Adapter I210 Artigo nº: 11137188	Gigabit Ethernet network adapter PCIe x1 (single lane) server adapter single GigE port supports screw lock connectors
	ZVA-Intel_Eth_Serv Adaptr_I350-T2V2 Artigo nº: 11168452	Gigabit Ethernet network adapter PCIe x2 (dual lane) server adapter single GigE port
	ZVA-PCIe-1672E-AE Artigo nº: 11168453	Gigabit Ethernet interface board PCIe x4 (quad lane) Dual GigE port Note: 4 lane PCI Express connector required

Housing accessories

	Tube Adapter A M47 hard anodized Artigo nº: 11185373	adapter to mount the Tube M47 hard anodized (11185370/11195425) to VCXG.I and VAX cameras thread: M47 length 2 mm
	Tube M47 hard anodized Artigo nº: 11185370	hard anodized lens protection with M47 thread optional tube extension with Tube Module 6mm (11185372) or Tube Module (11185371), length 12 mm. Use of several Tube Modules possible. thread: M47 length 44 mm
	Tube M47 hard anodized L12 Artigo nº: 11702640	hard anodized lens protection with M47 thread optional tube extension with Tube Module 6mm (11185372) or Tube Module (11185371), length 12 mm. Use of several Tube Modules possible. thread: M47 length 12 mm
	Tube M47 hard anod. scratchproof glass Artigo nº: 11701124	hard anodized lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (Generation 3) optional tube extension with Tube Module 6mm (11185372) or Tube Module (11185371), length 12 mm. Use of several Tube Modules possible. thread: M47 length 44 mm
	Tube Module 6 mm M47 hard anodized Artigo nº: 11185372	modular extension of the lens protection thread: M47 length 6 mm
	Tube Module 12 mm M47 hard anodized Artigo nº: 11185371	modular extension of the lens protection thread: M47 length 12 mm
	Tube Module 36 mm M47 hard anodized Artigo nº: 11211571	modular extension of the lens protection thread: M47 length 36 mm
	Tube Adapter B M62 hard anodized Artigo nº: 11185377	adapter to mount the Tube M62 hard anodized (11185374/11701125) to VCXG.I and VAX cameras thread: M62 length 2 mm
	Housing base set A VCXG.I r IP65/67 HA Artigo nº: 11207845	Hard anodized cylindric housing corpus for VCXG.I cameras for modular housing to meet Parma and Food & Beverage applications requirements optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). thread: M62 length 56 mm
	Tube M62 hard anodized Artigo nº: 11185374	hard anodized lens protection with M62 thread optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube M62 hard anod. scratchproof glass Artigo nº: 11701125	hard anodized lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (generation 3) optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube Module 6 mm M62 hard anodized Artigo nº: 11185376	modular extension of the lens protection thread: M62 length 6 mm
	Tube Module 12 mm M62 hard anodized Artigo nº: 11185375	modular extension of the lens protection thread: M62 length 12 mm
	Tube Module 36 mm M62 hard anodized Artigo nº: 11198906	modular extension of the lens protection thread: M62 length 36 mm
	Tube Adapter D M92 hard anodized Artigo nº: 11704311	adapter to mount the Tube M92 hard anodized (11704312) to VCX.I and VAX cameras thread: M92 length 2 mm
	Tube M92 hard anodized PMMA Artigo nº: 11704312	hard anodized lens protection with M92 thread optional tube extension with Tube Module 6mm (11704395) or Tube Module (11704397), length 12 mm. Use of several Tube Modules possible. thread: M92 length 70 mm
	Tube Module 6 mm M92 hard anodized Artigo nº: 11704395	modular extension of the lens protection thread: M92 length 6 mm
	Tube Module 12 mm M92 hard anodized Artigo nº: 11704397	modular extension of the lens protection thread: M92 length 12 mm
	Tube Module 36 mm M92 hard anodized Artigo nº: 11704394	modular extension of the lens protection thread: M92 length 36 mm
	Housing base set C V4A VCXG.I r IP65/67 Artigo nº: 11704019	Housing base set in hygienic design (EHEDG conform) to house VCXG.I cameras, IP69K protection Housing corpus with clamp elements to position the chosen VCXG.I camera M40 hygienic gland and M40 stainless steel counter nut to for fixation at the machine wall sealed up cable gland for IP68 protection inside the machine tube thread: M60 length 440 mm especially suitable for Pharma and Food & Beverage applications (incl. Splash and food zones) To be ordered separately: stainless steel lens protection Tube M60 V4A IP69K (11208732) necessary to close the housing available
	Tube M62 V4A PMMA Artigo nº: 11704017	stainless steel lens protection with PMMA cover glass (FDA certified) suitable for Housing base set C V4A VCXG.I r IP65/67 thread: M62 length 58 mm
	Tube M62 V4A scratchproof glass Artigo nº: 11704018	stainless steel lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (generation 3) optional tube extension with Tube Module 6mm M62 V4A (11704016), Tube Module 12 mm M62 V4A (11704015) or Tube Module 36 mm M62 V4A (11704015). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube Module 6 mm M62 V4A Artigo nº: 11704016	modular extension of the lens protection (for Housing base set C V4A VCXG.I r IP65/67) material: stainless steel thread: M62 length 6 mm
	Tube Module 12 mm M62 V4A Artigo nº: 11704015	modular extension of the lens protection (for Housing base set C V4A VCXG.I r IP65/67) material: stainless steel thread: M62 length 12 mm
	Tube Module 36 mm M62 V4A Artigo nº: 11704014	modular extension of the lens protection (for Housing base set C V4A VCXG.I r IP65/67) material: stainless steel thread: M62 length 36 mm
	Housing base set B V4A VCXG.I r IP69K Artigo nº: 11207844	Housing base set in hygienic design (EHEDG conform) to house VCXG.I cameras, IP69K protection Housing corpus with clamp elements to position the chosen VCXG.I camera M40 hygienic gland and M40 stainless steel counter nut to for fixation at the machine wall sealed up cable gland for IP68 protection inside the machine tube thread: M60 length 440 mm especially suitable for Pharma and Food & Beverage applications (incl. Splash and food zones) To be ordered separately: stainless steel lens protection Tube M60 V4A IP69K (11208732) necessary to close the housing available
	Housing V4A IP69K Mounting Tool Artigo nº: 11208719	Mounting tool to seal the stainless steel V4A VCXG.I r IP69K housing system
	Tube M60 V4A IP69K Acryl Artigo nº: 11208732	stainless steel lens protection with PMMA cover glass (FDA certified) suitable for Housing base set B V4A VCXG.I r IP69K (11208744) thread: M60 length 31 mm
	Cover Glass Replacement Acryl 2" Artigo nº: 11217113	Housing base set in hygienic design (EHEDG conform) to house VCXG.I cameras, IP69K protection Housing corpus with clamp elements to position the chosen VCXG.I camera M40 hygienic gland and M40 stainless steel counter nut to for fixation at the machine wall sealed up cable gland for IP68 protection inside the machine tube thread: M60 length 440 mm especially suitable for Pharma and Food & Beverage applications (incl. Splash and food zones) To be ordered separately: stainless steel lens protection Tube M60 V4A IP69K (11208732) necessary to close the housing available
	Sealing ReplacementSet Housing V4A IP69K Artigo nº: 11217115	Housing base set in hygienic design (EHEDG conform) to house VCXG.I cameras, IP69K protection Housing corpus with clamp elements to position the chosen VCXG.I camera M40 hygienic gland and M40 stainless steel counter nut to for fixation at the machine wall sealed up cable gland for IP68 protection inside the machine tube thread: M60 length 440 mm especially suitable for Pharma and Food & Beverage applications (incl. Splash and food zones) To be ordered separately: stainless steel lens protection Tube M60 V4A IP69K (11208732) necessary to close the housing available
	Rotation lock M40 VA4 IP69K Artigo nº: 11208731	Rotation lock for Housing base set B V4A VCXG.I r IP69K (11208744) with clamping part for safe position locking

Lens accessories

	Filter CL/27 (R2) ROT PENTAX Artigo nº: 11006551	Ricoh color filter (red)
	Filter Pol PENTAX PL27 Artigo nº: 11092000	Ricoh polarization filter linear filter thread
	ZVI-FILTER POL. PL30.5 C91353 Artigo nº: 11175428	Ricoh polarization filter linear filter thread M30.5
	ZVI-Filter Pol. PL40.5 C91301 Artigo nº: 11167713	Ricoh polarization filter linear filter thread M40.5
	ZVL-Adapter S-Mount / C-Mount Artigo nº: 11167984	Adapter S-mount / C-mount
	ZVF-Filter Holder Mounting Tool Artigo nº: 11177601	Mounting tool to screw in filter holders
	Close-up ring set ZVS-FP-RGST six-piece Artigo nº: 11010529	Close-up ring set ZVS-FP-RGST six-piece 0,5, 1, 5, 10, 20, 40 mm

Lens

	ZVL-E3196B Artigo nº: 11701908	Evetar lens 12 mm F 2,0 format 1/1,8" M.O.D. 0,3 m S-mount
	ZVL-M0828-MPW3 Artigo nº: 11703660	Computar lens 8 mm F 2,8-16 format 2/3″ M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-M1228-MPW3 Artigo nº: 11704871	Computar lens 12 mm F 2,8-16 format 2/3″ M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-M1628-MPW3 Artigo nº: 11704872	Computar lens 16 mm F 2,8-16 format 2/3″ M.O.D. 0,25 m locating screw for aperture and focus C-mount
	ZVL-M2528-MPW3 Artigo nº: 11704873	Computar lens 25 mm F 2,8-16 format 2/3″ M.O.D. 0,2 m locating screw for aperture and focus C-mount
	ZVL-M3528-MPW3 Artigo nº: 11704874	Computar lens 35 mm F 2,8-16 format 2/3″ M.O.D. 0,25 m locating screw for aperture and focus C-mount
	ZVL-M5028-MPW3 Artigo nº: 11704875	Computar lens 50 mm F 2,8-16 format 2/3″ M.O.D. 0,3 m locating screw for aperture and focus C-mount
	ZVL-LM6HC Artigo nº: 11215056	Kowa lens 6 mm F 1,8-16 format 1" M.O.D. 0,1 m C-mount
	Obj Kowa LM8HC 8mm/f1,4 Artigo nº: 11092599	Kowa lens 8 mm F 1,4-16 format 1" M.O.D. 0,1 m C-mount
	Obj Kowa LM12HC 12mm/f1,4 Artigo nº: 11092600	Kowa lens 12,5 mm F 1,4-16 format 1" M.O.D. 0,3 m C-mount
	Obj Kowa LM16HC 16mm/f1,4 Artigo nº: 11092601	Kowa lens 16 mm F 1,4-16 format 1" M.O.D. 0,3 m C-mount
	Obj Kowa LM25HC 25mm/f1,4 Artigo nº: 11092602	Kowa lens 25 mm F 1,4-16 format 1" M.O.D. 0,3 m C-mount
	Obj Kowa LM35HC 35mm/f1,4 Artigo nº: 11143330	Kowa lens 35 mm F 1,4-16 format 1" M.O.D. 0,3 m C-mount
	Obj Kowa LM50HC 50mm/f1,4 Artigo nº: 11143331	Kowa lens 50 mm F 1,4-16 format 1" M.O.D. 0,5 m C-mount
	Obj Kowa LM12HC-SW 12,5mm/f1,4 Artigo nº: 11097919	Kowa lens 12,5 mm F 1,4-16 format 1" locating screw for aperture and focus via RS485 interface M.O.D. 0,9 m C-mount
	Obj Kowa LM25HC-SW 25mm/f1,4 Artigo nº: 11092603	Kowa lens 25 mm F 1,4-16 format 1" M.O.D. 0,3 m SWIR optimized C-mount
	Obj Kowa LM35HC-SW 35mm/f1,4 Artigo nº: 11092605	Kowa lens 35 mm F 1,4-16 format 1" M.O.D. 0,4 m SWIR optimized C-mount
	Obj Kowa LM50HC-SW 50mm/f1,4 Artigo nº: 11087250	Kowa lens 50mm F1,4-16 format 1" M.O.D. 0,6 m SWIR optimized C-mount
	ZVL-LM3NCM 3,5mm/f2,4 Artigo nº: 11116658	Kowa lens 3,5 mm F 2,4-14 format 1/1.8'' M.O.D. 0,1 m C-mount
	Obj Kowa LM8JCM 8mm/f1,4 Artigo nº: 11092788	Kowa lens 8 mm F 1,4 format 2/3" M.O.D. 0,1 m C-mount
	Obj TOURMALINE 2,8/50 C Artigo nº: 11037739	Schneider Kreuznach lens 50 mm F 2,8-16 format 1.3" M.O.D. 0,135 m C-mount
	Obj CITRINE 1,4/17 C Artigo nº: 10170041	Schneider Kreuznach lens 17 mm F 1,4-11 format 2/3" M.O.D. 0,16 m C-mount
	Obj CITRINE 1,4/23 C Artigo nº: 11035165	Schneider Kreuznach lens 23 mm F 1,4-11 format 2/3" M.O.D. 0,211 m C-mount
	Obj TURQUOISE 1,8/16 C Artigo nº: 11076106	Schneider Kreuznach lens 16 mm F 1,8-22 format 1" M.O.D. 0,155 m C-mount
	Obj CITRINE 1,8/4,8 C Artigo nº: 11035760	Schneider Kreuznach lens 4,8 mm F 1,8-8 format 2/3" M.O.D. 0,037 m C-mount
	Obj CITRINE 1,4/12 C Artigo nº: 10170038	Schneider Kreuznach lens 12 mm F 1,4-11 format 2/3" M.O.D. 0,614 m C-mount
	Obj TURQUOISE 1,9/10 C Artigo nº: 11037743	Schneider Kreuznach lens 10 mm F 1,9-16 format 1" M.O.D. 0,092 m C-mount
	Obj CITRINE 1,4/8 C Artigo nº: 11035932	Schneider Kreuznach lens 8 mm F 1.4-8 format 2/3" M.O.D. 0.072 m C-mount

Network components

GigE Power Switch

Artigo nº: 11008795

GigE switch
PoE and Jumbo Frame support
4x 1000base-T
DIN rail mounting
operating voltage: 24-48 V; PoE requires 48 V

Cable

	CAM12.X8-11230367 Artigo nº: 11230367	M12, male, X-coded, 8-poles; PUR, 500 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230493 Artigo nº: 11230493	M12, male, X-coded, 8-poles; PUR, 1000 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230494 Artigo nº: 11230494	M12, male, X-coded, 8-poles; PUR, 1500 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230495 Artigo nº: 11230495	M12, male, X-coded, 8-poles; PUR, 2000 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	Cable GigE M12X/RJ45, STP 2.0m, flex Artigo nº: 11185139	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 2,0 m
	Cable GigE M12X/RJ45, STP 5.0m, flex Artigo nº: 11195760	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 5,0 m
	Cable GigE M12X/RJ45, STP 10.0m, flex Artigo nº: 11195761	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 10,0 m
	Cable GigE M12X/RJ45, STP 15.0m, flex Artigo nº: 11195762	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 15,0 m
	Cable GigE M12X/RJ45, STP 20.0m, flex Artigo nº: 11196995	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 20,0 m
	Cable GigE M12X/RJ45, STP, 2.0m, flex, 90° Artigo nº: 11195125	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic apllications (+/- 180°/0,5m, min. 1.000.000 torsion cycles) length 2,0 m
	Cable GigE M12X/RJ45, STP, 5.0m, flex, 90° Artigo nº: 11195123	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 5,0 m
	Cable GigE M12X/RJ45, STP, 10.0m, flex, 90° Artigo nº: 11195122	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 10,0 m
	Cable GigE M12X/RJ45, STP, 20.0m, flex, 90° Artigo nº: 11195121	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 20,0 m
	Cable GigE M12X/RJ45, STP, 30.0m, flex, 90° Artigo nº: 11195120	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 30,0 m
	Cable GigE M12X/RJ45, STP 30.0m, flex Artigo nº: 11185190	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 30,0 m
	Adapter Cable TX to VCXG.I VLXT Adapter Cable Artigo nº: 11701126	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera and I/Os and 4x M8/3-pin female connectors for illuminations The I/O voltage is directly distributed to the illuminations. length 40 cm (split at 20 cm) available
	Cable Power Adapter M12/DC Connector Artigo nº: 11048083	shielded adapter connection cable M12/12-pin male connector to confectioned DC connector length 2,0 m manufactured cable: 11201118 ESG 34JP0200GS
	ESG 34JP0200GS Shielded cable 12 wires, female connector, 2,0 m Artigo nº: 11201118	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESG 34JP0500GS Shielded cable 12 wires, female connector, 5,0 m Artigo nº: 11195097	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESG 34JP1000GS Shielded cable 12 wires, female connector, 10,0 m Artigo nº: 11195098	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESG 34JP2000GS Shielded cable 12 wires, female connector, 20,0 m Artigo nº: 11195099	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 20,0 m
	ESW 33JP0200GS 90° shielded cable 12 wires, female connector, 2,0 m Artigo nº: 11201128	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESW 33JP0500GS 90° shielded cable 12 wires, female connector, 5,0 m Artigo nº: 11195094	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESW 33JP1000GS 90° shielded cable 12 wires, female connector, 10,0 m Artigo nº: 11195095	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESW 33JP2000GS 90° shielded cable 12 wires, female connector, 20,0 m Artigo nº: 11195096	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 20,0 m

Mountings and heat sinks

	Mounting Adapter Type D (Front) Artigo nº: 11165176	mounting adapter for VCXU, VCXG and VCXG.I cameras incl. screw (hexagon socket) stable front side mounting
	Mounting Adapter Type A (Front) Artigo nº: 11002638	camera mounting adapter for TX, PX, VCXG.I and VisiLine cameras incl. screws (hexagon socket) and washers stable front side mounting
	Mounting Adapter Type B (Tripod) Artigo nº: 11003060	camera mounting adapter for TX, VisiLine, VisiLine IP, VCXG.I, LXG, LXC, PX and SX/HX cameras incl. screws (hexagon socket) and washers stable bottom and tripod mounting
	Mounting Adapter Type C Artigo nº: 11053252	camera mounting adapter for TX, VisiLine, VisiLine IP, VCXG.I, LX and HX cameras incl. screws (hexagon socket) and washers stable sidewise mounting

Illumination accessories

	ZVI-CONNECT_CameraExtension_CX.I_Type1 Artigo nº: 11701629	mounting adapter for illuminations Rondo LX and HELIOS-130 to VCXG.I cameras enables use of M62 tube system
	ZVI-Polarizer_FLDR_i90B Artigo nº: 11167410	Polarization filter for Falcon illumination FLDR-i90B
	ZVI-Polarizer_holder_FLDR_i90B Artigo nº: 11167411	Mounting adapter for polarization filter for Falcon FLDR-i90B illuminations: ZVI-Polarizer_FLDR-i90B (11167410) incl. screws
	ZVI-FLDR_i90B_DP_Diffuser A1_421 Artigo nº: 11167413	Diffusor with drilling holes and screws for Falcon illumination FLDR-i90B
	Multi headed cable Type A4 Split cable for illumination Artigo nº: 11207774	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera, 1x M8/4-pin male connector to power the I/Os and illuminations and 4x M8/4-pin female connector for illuminations Separate powering of camera and illumination. Double version of Output 1. length 40 cm (split at 20 cm) available
	Multi headed cable Type B1 Split cable for illumination Artigo nº: 11214470	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera and I/Os and 4x M8/3-pin female connectors for illuminations The I/O voltage is directly distributed to the illuminations. length 40 cm (split at 20 cm) available
	Multi headed cable Type B2 Split cable for illumination Artigo nº: 11214471	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera and I/Os and 4x M8/3-pin female connectors for illuminations The I/O voltage is directly distributed to the illuminations. length 40 cm (split at 20 cm) available
	Multi headed cable Type B4 Split cable for illumination Artigo nº: 11207776	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera and I/Os and 4x M8/3-pin female connectors for illuminations The I/O voltage is directly distributed to the illuminations. length 40 cm (split at 20 cm) available
	Multi headed cable Type C4 Split cable for illumination Artigo nº: 11207777	plit cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera, I/Os as well as illuminations and 4x M8/3-pin female connectors for illuminations The I/O voltage is distributed to the illuminations through the camera as a normal trigger signal using the cameras power output. length 40 cm (split at 20 cm) available
	Multi headed cable Type E1 Split cable for illumination Artigo nº: 11701467	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera and I/Os and 4x M8/3-pin female connectors for illuminations The I/O voltage is directly distributed to the illuminations. length 40 cm (split at 20 cm) available
	Multi headed cable Type E2 Split cable for illumination Artigo nº: 11701465	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera and I/Os and 4x M8/3-pin female connectors for illuminations The I/O voltage is directly distributed to the illuminations. length 40 cm (split at 20 cm) available
	Multi headed cable Type E4 Split cable for illumination Artigo nº: 11701466	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera and I/Os and 4x M8/3-pin female connectors for illuminations The I/O voltage is directly distributed to the illuminations. length 40 cm (split at 20 cm) available

Illumination

	FFPR-i100-W Artigo nº: 11086540	flashable LED dark field illumination white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 100 mm
	FLDL-i150x15-W Artigo nº: 11086539	flashable LED bar light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 158 mm × 17 mm × 20 mm housing
	FLDL-TP-Si200x100-W Artigo nº: 11086537	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 116 mm × 228 mm × 23,5 mm housing
	FLDL-TP-Si36-W Artigo nº: 11086536	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 47 mm × 47 mm × 15 mm housing
	FLDL-TP-Si85x77-W Artigo nº: 11086538	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 95 mm × 95 mm × 15 mm housing
	FLDM-i100-W Artigo nº: 11086541	flashable LED dome light white 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 130 mm
	FLDR-i90B-IR24 Artigo nº: 11090900	flashable LED ring light IR 875 nm 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLDR-i90B-SR24 Artigo nº: 11154321	flashable LED ring light red (626 nm) 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLDR-i90B-W Artigo nº: 11085869	flashable LED ring light white 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLFL-Si60-IR24 Artigo nº: 11095910	flashable LED back light NIR diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 94 mm × 94 mm × 10 mm housing
	ZVI-FLDL-i86x15-W Artigo nº: 11197768	flashable LED bar light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m dimensions: 18 mm × 95 mm × 20 mm housing
	ZVI-LED Spot5WFL-B/SPS-220 Artigo nº: 11175036	LED spot light blue 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-Adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-IR850/SPS-220 Artigo nº: 11175035	LED spot light infrared 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-Adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-R/SPS-220 Artigo nº: 11175034	LED spot light red 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-adapter cable (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-W/SPS-220 Artigo nº: 11175031	LED spot light white 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-ARCUSM_24VDC_WEIß_120° ARCUS-M white 24VDC with M8 connector Artigo nº: 11130183	flashable LED dark field illumination white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 120 mm
	ZVI-HILIGHT120_24VDC_WEIß HI-LIGHT-120 white 24VDC with M8 connector Artigo nº: 11130182	flashable LED back light white diffuse radiation angle 120° diameter: 94 mm 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 127 mm × 127 mm × 20 mm housing
	ZVI-HILIGHT80_24VDC_WEIß HI-LIGHT-80 white 24VDC with M8 connector Artigo nº: 11130181	flashable LED back light white diffuse radiation angle 80° diameter: 94 mm 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector dimensions: 87 mm × 87 mm × 20 mm housing
	ZVI-LOGO2_24VDC_ROT617NM_30° LOGO-2 red 617nm 30° 24VDC with M8 connector Artigo nº: 11130184	flashable LED bar light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 74 mm × 15 mm × 17 mm housing
	ZVI-HELIOS-130_IP65_weiß_80°_24VDC_M8 HELIOS-130 IP65 white 80° 24VDC with M8 connector Artigo nº: 11701627	flashable LED ring light white radiation angle 80° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 134 mm IP65 protection
	ZVI-RONDOLX_24VDC_IR850NM_120° RONDO-LX IR 850nm 120° 24VDC with M8 connector Artigo nº: 11130150	flashable LED ring light infrared (850 nm) radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-RONDOLX_24VDC_IR850NM_50° RONDO-LX IR 850nm 50° 24VDC with M8 connector Artigo nº: 11130176	flashable LED ring light infrared (850 nm) radiation angle 50° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-RONDOLX_24VDC_WEIß_120° RONDO-LX white 120° 24VDC with M8 connector Artigo nº: 11130179	flashable LED ring light white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-TOPLIGHT80_24VDC_rot617nm_30° TOPLIGHT80 red 617nm 30° 24VDC Artigo nº: 11135012	flashable LED incident light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 87 mm × 87 mm × 20 mm housing
	ZVI-TOPLINED1_24VDC_ROT617NM_30° TOP-LINE-D1 red 617nm 30° 24VDC M8 1-canal Artigo nº: 11130187	flashable LED bar light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing
	ZVI-TOPLINED1_24VDC_SHWEIß_120° TOP-LINE-D1 SH white 120° 24VDC M8 1-canal Artigo nº: 11130186	flashable LED bar light SH white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing
	ZVI-TOPLINED1_24VDC_WEIß_120° TOP-LINE-D1 white 120° 24VDC M8 1-canal Artigo nº: 11130185	flashable LED bar light white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing