VLXT-83UV.I

Numéro d'article: 11725745

2848 × 2832 px
Sony IMX487
2/3″ CMOS
150 fps
10 GigE
Spectrum: UV (200–400 nm)
Firmware update required to use RDMA

1 pièces immédiatement disponibles en stock

Caractéristiques techniques

Tout afficher

information du capteur

Sensor

Sony IMX487

Mono/Color

Sensor type

2/3″ CMOS

Shutter type

Global shutter

Résolution

2848 × 2832 px

Pixel size

2.74 × 2.74 µm

Exposure time

0,001 … 60000 ms

Dark noise

2,5 e-

Saturation capacity

9000 e-

Dynamic range

70 dB

Signal-to-noise ratio

40 dB

Quantum efficiency

39 % @ 265 nm

formats d'acquisition

Image formats, interface frame rate max.

Full Frame, 2848 × 2832 px, max. 150 fps
Binning 2×2, 1424 × 1416 px, max. 172 fps
Binning 2×1, 1424 × 2832 px, max. 172 fps
Binning 1×2, 2848 × 1416 px, max. 172 fps

Image formats, aquisition frame rate max. (Burst Mode)

Full Frame, 2848 × 2832 px, max. 172 fps

Pixel formats

Mono8
Mono10
Mono12
Mono12 Packed

Analog controls

Gain (0 … 48 dB)
Offset (0 … 255 LSB 12 Bit)

Color models

Mono
Raw Bayer
RGB
BGR

caractéristiques de l'appareil

Basic Functions

Exposure
Gain / Color Gain
Trigger / Exposure Active (Flash)
Binning 2x2
Partial Scan
Offset
Free Running Mode (Live Image)
Multi ROI

Auto Functions

Exposure Auto
Gain Auto

Image Pre-processing

Image Flipping (X/Y)
LUT / Gamma
Shading Correction
Edge Sharpening
Noise Reduction

Acquisition / Interface

Burst Mode
Adjustable Framerate
Short Exposure Time Enable
Device Link Throughput Limit
Internal Image Buffer

Synchronisation

free running
trigger

Trigger sources

Hardware
Software
ActionCommand

Trigger delay

0 … 2 s, tracking and buffering of up to 256 trigger signals

Process Synchronization

Events
Timer
Trigger Delay
Debouncer
Counter
Sequencer
Trigger via Action CMD (GigE)
Action CMD Request ID
Trigger ID inside Chunk
Additional Output Modes (e.g. Trigger Ready)
PWM (PWM Duration / PWM Duty Cycle)
Selectable Output format (e.g. Tri State, Push Pull)
Chunk data inside transferred image
Encoder support via Counter End trigger source
4 power outputs with up to 120 W (max. 48 V / 2.5 A)

Time synchronization IEEE 1588

IEEE 1588 / Master and Slave function
IEEE 1588 / Scheduled Action CMD
IEEE 1588 / Synchronized Acquisition Framerate

Additional Functions

User Set
Integrated temperature sensor
Readable additional information (e.g. sensor information)
Save Custom Data

Lens control

Corning liquid lens

Internal image buffer

1024 MB
127 images (Trigger Mode)
1 image (Free Running Mode)

Interfaces et connecteurs

Data interface

10 Gigabit Ethernet, Transfer rate 10000 Mbits/sec, Gigabit Ethernet, Transfer rate 1000 Mbits/sec, Fast Ethernet, Transfer rate 100 Mbits/sec, Connector: M12 / 8-pol x-coded (SACC-CI-M12FS-8CON-L180-10G)

Process interface

M12 / 12 pins a-coded (SACC-CI-M12MS-12CON-L180)

Power supply

via M12/12 pins a-coded

Données mécaniques

Lens mount

C-mount

Width

60 mm

Height

60 mm

Profondeur

99,7 mm

Poids

≤ 485 g

Matériau

aluminum, hard-anodized

Données électriques

Plage de tension +Vs

19,2 … 28,8 V DC (external power supply)

Puissance absorbée

Approx. 12.7 W @ 24 VDC and 150 fps

Flash memory size

128 kB

Conditions ambiantes

Operating temperature

0 … +60 ° @ T = measurement point

Humidity

0 … 90 % (non-condensing)

Classe de protection

IP 40
IP 54 (with mounted lens and cable)
IP 65 (with mounted tube and cable)
IP 67 (with mounted tube and cable)

E/S numériques

Lines

2 input lines
4 power output lines with pulse width modulation (PWM) (max. 48 V / max. 2,5 A)
RS232

Output line sources

Off
Exposure Active
Timer1
Readout Active
User0
User1
User2
TriggerReady

Conformité

Conformity

CE
RoHS

Logiciel

Tout afficher

Software

Baumer neoAPI (Windows, Linux, Linux ARM)
- Link
Baumer Camera Explorer (Windows, Linux, Linux ARM)
- Link
Baumer GAPI SDK v2.x (Windows, Linux, Linux ARM)
- Link
Baumer GAPI software examples
- Link
Third Party Software
- Link

Logiciel

Baumer IPConfig Tool v2.0.2 (Windows)
- EN (zip | 5 MB)

Téléchargements

Tout afficher

Fiche technique

Fiche technique – VLXT-83UV.I
- DE (pdf | 1 MB)
Fiche technique – VLXT-83UV.I
- EN (pdf | 1 MB)
Detailed data sheet – xxx
- EN (pdf | 526 KB)

Guide rapide

Quick Start Guide VLXT
- EN (pdf | 1 MB)

Instructions d'utilisation

User’s Guide VLXT.I / VLXT.FO cameras
- EN (pdf | 14 MB)

Certifications / Approbations

UL certification
- EN (pdf | 546 KB)

Additional information

EMVA 1288 Summary Sheet
- EN (pdf | 395 KB)
Compliant list for Baumer industrial cameras (10 GigE)
- EN (pdf | 626 KB)

Informations supplémentaires

Application Notes
- Link

Dessins

Tout afficher

Dessin d'encombrement

The selected altAttribute does not exist!

(png | 109 KB)

Schematic diagram

(png | 252 KB)

Accessoires

Tout afficher

Power supply

Power Supply 24V/1.0A Int. DC Connector

Numéro d'article: 11079750

power supply 24V/1,0A with adapters for EU, US, UK AU, KR
in combination with "Cable power adapter M12/DC connector" (11048083) suitable for VCXG.I(.XT), VLXT, VAX and VeriSens

Starter Kit

VLXT Starter Kit

Numéro d'article: 11204995

10-GigE PCIe interface board
GigE cable 5,0 m (M12/x-coded)
Power Supply 24 V/1.0 A with adapter cable M12/12-pin to DC connector
Tube system M62 with adapter (11193125) and tube (11185374)
Mounting Adapter Type C
Heat Sink Type B
camera not included

PCIe/Adapter

	ZVA-Intel_X550-T2_10GbE_Serv_Adapter Numéro d'article: 11190893	10-GigE PCIe interface board PCIe x4 (quad lane) converged network adapter dual GigE port max. power consumption 8.4 W (10 GigE single port use) / 13.0 W (10 GigE dual port use) incl. SW driver (CD)
	PCIe Ethernet Server Adapter I210 Numéro d'article: 11137188	Gigabit Ethernet network adapter PCIe x1 (single lane) server adapter single GigE port supports screw lock connectors
	ZVA-Intel_Eth_Serv Adaptr_I350-T2V2 Numéro d'article: 11168452	Gigabit Ethernet network adapter PCIe x2 (dual lane) server adapter single GigE port
	ZVA-PCIe-1672E-AE Numéro d'article: 11168453	Gigabit Ethernet interface board PCIe x4 (quad lane) Dual GigE port Note: 4 lane PCI Express connector required

Housing accessories

	Tube Adapter C M62 hard anodized Numéro d'article: 11193125	adapter to mount the Tube M62 hard anodized (11185374/11701125) to VLXT cameras thread: M62 length 2 mm
	Tube M62 hard anodized Numéro d'article: 11185374	hard anodized lens protection with M62 thread optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube Module 6 mm M62 hard anodized Numéro d'article: 11185376	modular extension of the lens protection thread: M62 length 6 mm
	Tube Module 12 mm M62 hard anodized Numéro d'article: 11185375	modular extension of the lens protection thread: M62 length 12 mm
	Tube Module 36 mm M62 hard anodized Numéro d'article: 11198906	modular extension of the lens protection thread: M62 length 36 mm
	Tube M62 hard anod. scratchproof glass Numéro d'article: 11701125	hard anodized lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (generation 3) optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm

Lens accessories

	Adapter TFL-Mount / C-Mount Numéro d'article: 11702566	Lens mount adapter from TFL-mount (camera) to C-Mount (lens)
	Filter CL/27 (R2) ROT PENTAX Numéro d'article: 11006551	Ricoh color filter (red)
	ZVI-FILTER POL. PL30.5 C91353 Numéro d'article: 11175428	Ricoh polarization filter linear filter thread M30.5
	ZVI-Filter Pol. PL40.5 C91301 Numéro d'article: 11167713	Ricoh polarization filter linear filter thread M40.5
	ZVF-Filter Holder Mounting Tool Numéro d'article: 11177601	Mounting tool to screw in filter holders

Lens

	ZVL-HF1635V-UV Numéro d'article: 11728662	Myutron lens 16 mm F 3.5 format 1" M.O.D. 0.095 m locating screw for aperture and focus C-mount suitable for UV and visible wavelengths (190 - 700 nm)
	ZVL-HF2528V-UV Numéro d'article: 11728663	Myutron lens 25 mm F 2.8 format 1" M.O.D. 0.091 m locating screw for aperture and focus C-mount suitable for UV and visible wavelengths (190 - 700 nm)
	ZVL-HF3535V-UV Numéro d'article: 11728664	Myutron lens 35 mm F 3.5 format 1" M.O.D. 0.191 m locating screw for aperture and focus C-mount suitable for UV and visible wavelengths (190 - 700 nm)
	ZVL-HF5035V-UV Numéro d'article: 11728665	Myutron lens 50 mm F 3.5 format 1" M.O.D. 0.183 m locating screw for aperture and focus C-mount suitable for UV and visible wavelengths (190 - 700 nm)

Network components

GigE Power Switch

Numéro d'article: 11008795

GigE switch
PoE and Jumbo Frame support
4x 1000base-T
DIN rail mounting
operating voltage: 24-48 V; PoE requires 48 V

Cable

	CAM12.X8-11230367 Numéro d'article: 11230367	M12, male, X-coded, 8-poles; PUR, 500 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230493 Numéro d'article: 11230493	M12, male, X-coded, 8-poles; PUR, 1000 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230494 Numéro d'article: 11230494	M12, male, X-coded, 8-poles; PUR, 1500 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230495 Numéro d'article: 11230495	M12, male, X-coded, 8-poles; PUR, 2000 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	Cable GigE M12X/RJ45, STP 2.0m, flex Numéro d'article: 11185139	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 2,0 m
	Cable GigE M12X/RJ45, STP 5.0m, flex Numéro d'article: 11195760	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 5,0 m
	Cable GigE M12X/RJ45, STP 10.0m, flex Numéro d'article: 11195761	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 10,0 m
	Cable GigE M12X/RJ45, STP 15.0m, flex Numéro d'article: 11195762	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 15,0 m
	Cable GigE M12X/RJ45, STP 20.0m, flex Numéro d'article: 11196995	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 20,0 m
	Cable GigE M12X/RJ45, STP 30.0m, flex Numéro d'article: 11185190	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 30,0 m
	Cable GigE M12X/RJ45, STP, 5.0m, flex, 90° Numéro d'article: 11195123	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 5,0 m
	Cable GigE M12X/RJ45, STP, 10.0m, flex, 90° Numéro d'article: 11195122	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 10,0 m
	Adapter Cable TX to VCXG.I VLXT Adapter Cable Numéro d'article: 11701126	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 1x M8/3-pin female connector for one illumination The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Cable Power Adapter M12/DC Connector Numéro d'article: 11048083	shielded adapter connection cable M12/12-pin male connector to confectioned DC connector length 2,0 m manufactured cable: 11201118 ESG 34JP0200GS
	ESG 34JP0200GS Shielded cable 12 wires, female connector, 2,0 m Numéro d'article: 11201118	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESG 34JP0500GS Shielded cable 12 wires, female connector, 5,0 m Numéro d'article: 11195097	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESG 34JP1000GS Shielded cable 12 wires, female connector, 10,0 m Numéro d'article: 11195098	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESG 34JP2000GS Shielded cable 12 wires, female connector, 20,0 m Numéro d'article: 11195099	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 20,0 m
	ESW 33JP0200GS 90° shielded cable 12 wires, female connector, 2,0 m Numéro d'article: 11201128	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESW 33JP0500GS 90° shielded cable 12 wires, female connector, 5,0 m Numéro d'article: 11195094	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESW 33JP1000GS 90° shielded cable 12 wires, female connector, 10,0 m Numéro d'article: 11195095	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESW 33JP2000GS 90° shielded cable 12 wires, female connector, 20,0 m Numéro d'article: 11195096	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 20,0 m
	Cable GigE M12X/RJ45, STP, 30.0m, flex, 90° Numéro d'article: 11195120	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 30,0 m
	Cable GigE M12X/RJ45, STP, 20.0m, flex, 90° Numéro d'article: 11195121	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 20,0 m
	Cable GigE M12X/RJ45, STP, 2.0m, flex, 90° Numéro d'article: 11195125	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic apllications (+/- 180°/0,5m, min. 1.000.000 torsion cycles) length 2,0 m

Mountings and heat sinks

	Mounting Adapter Type C Numéro d'article: 11053252	camera mounting adapter for TX, VisiLine, VisiLine IP, VCXG.I, LX and HX cameras incl. screws (hexagon socket) and washers stable sidewise mounting
	Mounting Adapter Type H Numéro d'article: 11191852	camera mounting adapter for cameras of the CX, LX and QX series incl. screw (hexagon socket) rotatable mounting
	Heat Sink Type A Numéro d'article: 11037580	heat sink for TX, VCXG.I, VisiLine, VisiLine IP, LX and HX cameras incl. screws (hexagon socket) and washers 48 mm x 33 mm x 16,5 mm
	Heat Sink Type B Numéro d'article: 11114702	heat sink for TX, VCXG.I, VisiLine, VisiLine IP, LX and HX cameras incl. screws (hexagon socket) and washers 50 mm x 50 mm x 40 mm

Illumination

	Baumer ZVI-BL-310/27-365HP Numéro d'article: 11729036	Flashable UV LED bar light Wavelength 365 nm Radiation angle 45° Integrated LED controller with 4 operating modes IP54
	Baumer ZVI-RL-80/141-365HP Numéro d'article: 11729040	Flashable UV LED ring light Wavelength 365 nm Radiation angle 45° Integrated LED controller with 4 operating modes IP54

Au sommet

Série LX

VLXT-83UV.I

10 Gigabit Ethernet, 8.0 Megapixel, Ultraviolet

Caractéristiques techniques

information du capteur

formats d'acquisition

caractéristiques de l'appareil

Interfaces et connecteurs

Données mécaniques

Données électriques

Conditions ambiantes

E/S numériques

Conformité

Logiciel

Software

Logiciel

Téléchargements

Fiche technique

Guide rapide

Instructions d'utilisation

Certifications / Approbations

Additional information

Informations supplémentaires

Dessins

Dessin d'encombrement

Schematic diagram

Accessoires

Power supply

Starter Kit

PCIe/Adapter

Housing accessories

Lens accessories

Lens

Network components

Cable

Mountings and heat sinks

Illumination