VLXT-90M.FO

Article no.: 11208340

4096 × 2160 px
Sony IMX255
1″ CMOS
95 fps
10 GigE

available on request

Technical data

show all

Sensor information

Sensor

Sony IMX255 Gen2

Mono/Color

Mono

Sensor type

1″ CMOS

Shutter type

Global shutter

Resolution

4096 × 2160 px

Pixel size

3.45 × 3.45 µm

Exposure time

0.001 … 60000 ms

Data quality (EMVA 1288 typical)

Dark noise

2.12 e-

Saturation capacity

9379 e-

Dynamic range

70.6 dB

Signal-to-noise ratio

39.7 dB

Quantum efficiency

64.7 % @ 536 nm

Acquisition formats

Image formats, interface frame rate max.

Full Frame, 4096 × 2160 px, max. 95 fps
Binning 2×2, 2048 × 1080 px, max. 184 fps
Binning 2×1, 2048 × 2160 px, max. 95 fps
Binning 1×2, 4096 × 1080 px, max. 95 fps

Image formats, aquisition frame rate max. (Burst Mode)

Full Frame, 4096 × 2160 px, max. 95 fps

Pixel formats

Mono8
Mono10
Mono12
Mono12 Packed

Image preprocessing

Analog controls

Gain (0 … 48 dB)
Offset (0 … 255 LSB 12 Bit)

Color models

Mono

Camera features

Basic Functions

Exposure
Gain / Color Gain
Trigger / Exposure Active (Flash)
Binning 2x2
Partial Scan
Offset
Free Running Mode (Live Image)
Multi ROI

Auto Functions

Exposure Auto
Gain Auto

Image Pre-processing

Image Flipping (X/Y)
LUT / Gamma
Shading Correction
Edge Sharpening
Noise Reduction

Acquisition / Interface

Burst Mode
Adjustable Framerate
Short Exposure Time Enable
Device Link Throughput Limit
Internal Image Buffer

Synchronization

free running
trigger

Trigger sources

Hardware
Software
ActionCommand

Trigger delay

0 … 2 s, tracking and buffering of up to 256 trigger signals

Process Synchronization

Events
Timer
Trigger Delay
Debouncer
Counter
Sequencer
Trigger via Action CMD (GigE)
Action CMD Request ID
Trigger ID inside Chunk
Additional Output Modes (e.g. Trigger Ready)
PWM (PWM Duration / PWM Duty Cycle)
Selectable Output format (e.g. Tri State, Push Pull)
Chunk data inside transferred image
Encoder support via Counter End trigger source
4 power outputs with up to 120 W (max. 48 V / 2.5 A)

Time synchronization IEEE 1588

IEEE 1588 / Master and Slave function
IEEE 1588 / Scheduled Action CMD
IEEE 1588 / Synchronized Acquisition Framerate

Additional Functions

User Set
Integrated temperature sensor
Readable additional information (e.g. sensor information)
Save Custom Data

Lens control

Corning liquid lens

Sequencer

Automated control for series of images using different sets of parameters

Sequencer parameter

Exposure time
gain factor
output line
ROI Offset x
ROI Offset y

Internal image buffer

1024 MB
117 images (Trigger Mode)
1 image (Free Running Mode)

Interfaces and connectors

Data interface

10 Gigabit Ethernet, Transfer rate 10000 Mbits/sec, Connector: SFP+ cage

Process interface

M12 / 12 pins a-coded (SACC-CI-M12MS-12CON-L180)

Power supply

via M12/12 pins a-coded

Mechanical data

Lens mount

C-mount

Width

60 mm

Height

60 mm

Depth

79.6 mm

Weight

≤ 415 g

Material

aluminum

Electrical data

Voltage supply range +Vs

12 … 24 V DC (external power supply)

Non-volatile memory

Flash memory size

128 kB

Environmental conditions

Operating temperature

0 … +65 ° @ T = measurement point

Humidity

10 … 90 % (non-condensing)

Protection class

IP 40
IP 54 (with mounted tube and cable)
IP 65 (with mounted tube and cable)
IP 67 (with mounted tube and cable)

Digital I/Os

Lines

2 input lines
4 power output lines with pulse width modulation (PWM) (max. 48 V / max. 2,5 A)
RS232

Conformity

Conformity

CE
RoHS
UL recognized

Software

show all

Software packages

Baumer neoAPI (Windows, Linux, Linux ARM)
- Link
Baumer Camera Explorer (Windows, Linux, Linux ARM)
- Link
Baumer GAPI SDK v2.x (Windows, Linux, Linux ARM)
- Link
Baumer GAPI software examples
- Link
Third Party Software
- Link

Software

Baumer IPConfig Tool v2.0.2 (Windows)
- EN (zip | 5 MB)

Downloads

show all

Data sheet

Data sheet – VLXT-90M.FO
- DE (pdf | 1005 KB)
Data sheet – VLXT-90M.FO
- EN (pdf | 1006 KB)
Detailed data sheet – VLXT-90M.FO
- EN (pdf | 579 KB)

Quickstart

Quick Start Guide LXT.FO
- EN (pdf | 1 MB)

Operating Manual

User’s Guide VLXT.I / VLXT.FO cameras
- EN (pdf | 14 MB)

Certificates / approvals

CE certification
- EN/DE/BG/CZ/DK/ES/FI/FR/GR/HU/IT/LT/LV/NL/NO/PL/PT/RO/SK/SI (pdf | 173 KB)

Additional information

EMVA 1288 Summary Sheet
- EN (pdf | 227 KB)
Compliant list for Baumer industrial cameras (10 GigE)
- EN (pdf | 626 KB)

Application notes

Application Notes
- Link

CAD

VLXT-90M.FO / STEP
- (zip | 616 KB)

Drawings

show all

Dimension drawing

The selected altAttribute does not exist!

(png | 120 KB)

Schematic diagram

(png | 292 KB)

Accessories

show all

Power supply

Power Supply 24V/1.0A Int. DC Connector

Article no.: 11079750

power supply 24V/1,0A with adapters for EU, US, UK AU, KR
in combination with "Cable power adapter M12/DC connector" (11048083) suitable for VCXG.I(.XT), VLXT, VAX and VeriSens

Starter Kit

VLXT.FO Starter Kit

Article no.: 11213910

Fiber PCIe Interface Board
SFP+ 10-GigE cable 5,0 m
Process interface cable 2,0 m
Power Supply 24 V/1.0 A with adapter cable M12/12-pin to DC connector
Tube system M62 with adapter (11193125) and tube (11185374)
Mounting Adapter Type C
Heat Sink Type B
camera not included

PCIe/Adapter

	ZVA-DeLock_PCIe_Fiber_SFP+_10-GigE Article no.: 11700594	10-GigE PCIe interface board PCIe x4 (quad lane) Single SFP port for 10-GigE SFP+ transceiver Tehuti TN4010 chipset
	ZVA-INTEL_X710-T2L Article no.: 11722776	10-GigE PCIe interface board PCIe x8 dual GigE port max. power consumption 9.6 W (10 GigE dual port use) incl. SW driver (CD)

Housing accessories

	Tube Adapter C M62 hard anodized Article no.: 11193125	adapter to mount the Tube M62 hard anodized (11185374/11701125) to VLXT cameras thread: M62 length 2 mm
	Tube M62 hard anodized Article no.: 11185374	hard anodized lens protection with M62 thread optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube Module 6 mm M62 hard anodized Article no.: 11185376	modular extension of the lens protection thread: M62 length 6 mm
	Tube Module 12 mm M62 hard anodized Article no.: 11185375	modular extension of the lens protection thread: M62 length 12 mm
	Tube Module 36 mm M62 hard anodized Article no.: 11198906	modular extension of the lens protection thread: M62 length 36 mm
	Tube M62 hard anod. scratchproof glass Article no.: 11701125	hard anodized lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (generation 3) optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm

Lens accessories

	Filter CL/27 (R2) ROT PENTAX Article no.: 11006551	Ricoh color filter (red)
	Filter Pol PENTAX PL27 Article no.: 11092000	Ricoh polarization filter linear filter thread
	ZVI-FILTER POL. PL30.5 C91353 Article no.: 11175428	Ricoh polarization filter linear filter thread M30.5
	ZVI-Filter Pol. PL40.5 C91301 Article no.: 11167713	Ricoh polarization filter linear filter thread M40.5
	ZVL-Adapter S-Mount / C-Mount Article no.: 11167984	Adapter S-mount / C-mount
	ZVF-Filter Holder Mounting Tool Article no.: 11177601	Mounting tool to screw in filter holders

Lens

	Obj TOURMALINE 2,8/50 C Article no.: 11037739	Schneider Kreuznach lens 50 mm F 2,8-16 format 1.3" M.O.D. 0,135 m C-mount
	Obj Kowa LM12XC 12mm/f2,0 Article no.: 11092574	Kowa lens 12 mm F 2,0-22 format 4/3" M.O.D. 0,1 m C-mount
	Obj Kowa LM16XC 16mm/f2,0 Article no.: 11092592	Kowa lens 16 mm F 2,0-22 format 4/3" M.O.D. 0,1 m C-mount
	Obj Kowa LM25XC 25mm/f2,0 Article no.: 11092593	Kowa lens 25 mm F 2,0-16 format 4/3" M.O.D. 0,15 m C-mount
	Obj Kowa LM35XC 35mm/f2,0 Article no.: 11092597	Kowa lens 35 mm F 2,0-22 format 4/3" M.O.D. 0,2 m C-mount
	Obj Kowa LM50XC 50mm/f2.0 Article no.: 11166201	Kowa lens 50 mm F 2,0-22 format 4/3" M.O.D. 0,3 m C-mount
	ZVL-V0828-MPY Article no.: 11181608	Computar lens 8 mm F 2,8-16 format 1,1" M.O.D. 0,2 m locating screw for aperture and focus C-mount
	ZVL-V1228-MPY Article no.: 11181609	Computar lens 12 mm F 2,8-16 format 1,1" M.O.D. 0,3 m locating screw for aperture and focus C-mount
	ZVL-V1628-MPY Article no.: 11181640	Computar lens 16 mm F 2,8-16 format 1,1" M.O.D. 0,3 m locating screw for aperture and focus C-mount
	ZVL-V2528-MPY Article no.: 11181641	Computar lens 25 mm F 2,8-16 format 1,1" M.O.D. 0,3 m locating screw for aperture and focus C-mount
	ZVL-V3528-MPY Article no.: 11181642	Computar lens 35 mm F 2,8-16 format 1,1" M.O.D. 0,3 m locating screw for aperture and focus C-mount
	ZVL-V5028-MPY Article no.: 11181643	Computar lens 50 mm F 2,8-16 format 1,1" M.O.D. 0,55 m locating screw for aperture and focus C-mount
	ZVL-LM6FC24M Article no.: 11700795	Kowa lens 6,5 mm F 2,5-16 format 1,1" M.O.D. 0,1 m C-mount
	ZVL-LM8FC24M Article no.: 11700796	Kowa lens 8,5 mm F 2,5-16 format 1,1" M.O.D. 0,1 m C-mount
	ZVL-LM12FC24M Article no.: 11700791	Kowa lens 12 mm F 1,8-16 format 1,1" M.O.D. 0,1 m C-mount
	ZVL-LM16FC24M Article no.: 11700739	Kowa lens 16 mm F 1,8-16 format 1,1" M.O.D. 0,1 m C-mount
	ZVL-LM25FC24M Article no.: 11700738	Kowa lens 25 mm F 1,8-16 format 1,1" M.O.D. 0,1 m C-mount
	ZVL-LM35FC24M Article no.: 11700793	Kowa lens 35 mm F 1,8-16 format 1,1" M.O.D. 0,2 m C-mount
	ZVL-LM50FC24M Article no.: 11700794	Kowa lens 50 mmm F 1,8-16 format 1,1" M.O.D. 0,2 m C-mount
	ZVL-V0826-MPZ Article no.: 11700363	Computar lens 8 mm F 2,6-16 format 1″ M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-V1226-MPZ Article no.: 11700368	Computar lens 12 mm F 2,6-16 format 1″ M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-V1624-MPZ Article no.: 11700366	Computar lens 16 mm F 2,4-16 format 1″ M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-V2520-MPZ Article no.: 11700364	Computar lens 25 mm F 2,0-16 format 1″ M.O.D. 0,15 m locating screw for aperture and focus C-mount
	ZVL-V3522-MPZ Article no.: 11700365	Computar lens 35 mm F 2,2-16 format 1″ M.O.D. 0,2 m locating screw for aperture and focus C-mount
	ZVL-V5024-MPZ Article no.: 11700367	Computar lens 50 mm F 2,4-16 format 1″ M.O.D. 0,2 m locating screw for aperture and focus C-mount
	ZVL-Dimension_2.8/8_C Article no.: 11214035	Carl Zeiss lens 8 mm F 2,8-22 format 4/3'' M.O.D. 0,102 m locating screw for aperture and focus C-mount
	ZVL-Dimension_2/12_C Article no.: 11214036	Carl Zeiss lens 12 mm F 2,0-22 format 4/3'' M.O.D. 0,101 m locating screw for aperture and focus C-mount
	ZVL-Dimension_2/18_C Article no.: 11214038	Carl Zeiss lens 18 mm F 2,0-22 format 4/3'' M.O.D. 0,090 m locating screw for aperture and focus C-mount
	ZVL-Dimension_2/25_C Article no.: 11214039	Carl Zeiss lens 25 mm F 2,0-22 format 4/3'' M.O.D. 0,152 m locating screw for aperture and focus C-mount
	ZVL-Dimension_2/35_C Article no.: 11214040	Carl Zeiss lens 35 mm F 2,0-22 format 4/3'' M.O.D. 0,209 m locating screw for aperture and focus C-mount
	ZVL-Dimension_2/50_C Article no.: 11214041	Carl Zeiss lens 50 mm F 2,0-22 format 4/3'' M.O.D. 0,311 m locating screw for aperture and focus C-mount

Network components

	ZVN-Transceiver SPF+ FS Multi Mode Article no.: 11700593	10 GigE SFP+ Transceiver SFP+ module type: Multi Mode Fiber SFP-10GSR-85 max. cable distance 300 m via OM3 multi mode fiber wavelength 850 nm
	ZVN-Transceiver SPF+ FS Single Mode Article no.: 11700592	10 GigE SFP+ Transceiver SFP+ module type: Single Mode Fiber SFP-10GLR-31 max. cable distance 10 km via single mode fiber wavelength 1310 nm

Cable

	Adapter Cable TX to VCXG.I VLXT Adapter Cable Article no.: 11701126	Adapter to connect VCXG.I or VLXT cameras to existing TXG cabling Split cable M12/12-pin male connector to 1x M8/3-pin female connector (power) and 1x M8/4-pin female connector (I/Os) Protection class IP65/IP67 Length 0.4 m
	Cable Power Adapter M12/DC Connector Article no.: 11048083	shielded adapter connection cable M12/12-pin male connector to confectioned DC connector length 2,0 m manufactured cable: 11201118 ESG 34JP0200GS
	ESG 34JP0200GS Shielded cable 12 wires, female connector, 2,0 m Article no.: 11201118	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESG 34JP0500GS Shielded cable 12 wires, female connector, 5,0 m Article no.: 11195097	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESG 34JP1000GS Shielded cable 12 wires, female connector, 10,0 m Article no.: 11195098	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESW 33JP0200GS 90° shielded cable 12 wires, female connector, 2,0 m Article no.: 11201128	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESW 33JP0500GS 90° shielded cable 12 wires, female connector, 5,0 m Article no.: 11195094	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESW 33JP1000GS 90° shielded cable 12 wires, female connector, 10,0 m Article no.: 11195095	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	10-GigE DA Cable Copper SFP+/SFP+, 5.0m Article no.: 11700591	Copper cable for 10-GigE connection SFP+ module to SFP+ module (direct attached) length 5.0 m Cisco Coding
	Fiber Optical Cable SFP+/SFP+, 10,0 m Article no.: 11214518	Fiber Optical cable for 10-GigE connection SFP+ module to SFP+ module (direct attached) length 10.0 m Juniper Coding
	Fiber Optical Cable SFP+/SFP+, 10,0 m, flex Article no.: 11214517	Fiber Optical cable for 10-GigE connection SFP+ module to SFP+ module (direct attached) cable carrier compatible suitable for robotic applications length 10.0 m Juniper Coding
	Fiber Optical Cable XSsh/LC, IP67, 20,0m Article no.: 11213911	Fiber Optical cable for 10-GigE connection, multi mode SFP+ module to SFP+ module (SFP+ modules are not included and have to be ordered separately) high robustness - crush resistance 2100 N/cm length 20.0m IP65/67 in combination with “Housing Cable Adapter SFP+/IP67”
	Housing Cable Adapter SFP+/IP67 Article no.: 11213914	Housing adapter for VLXT.FO cameras use in combination with Harting fiber optical cable IP67 (11213911) to reach IP 65/67 protection class

Mountings and heat sinks

	Mounting Adapter Type C Article no.: 11053252	camera mounting adapter for TX, VisiLine, VisiLine IP, VCXG.I, LX and HX cameras incl. screws (hexagon socket) and washers stable sidewise mounting
	Mounting Adapter Type H Article no.: 11191852	camera mounting adapter for cameras of the CX, LX and QX series incl. screw (hexagon socket) rotatable mounting
	Heat Sink Type A Article no.: 11037580	heat sink for TX, VCXG.I, VisiLine, VisiLine IP, LX and HX cameras incl. screws (hexagon socket) and washers 48 mm x 33 mm x 16,5 mm
	Heat Sink Type B Article no.: 11114702	heat sink for TX, VCXG.I, VisiLine, VisiLine IP, LX and HX cameras incl. screws (hexagon socket) and washers 50 mm x 50 mm x 40 mm

Illumination accessories

	ZVI-CONNECT_CameraExtension_VLXT.I_Type1 Article no.: 11701628	mounting adapter for illuminations Rondo LX and HELIOS-130 to VLXT.I cameras enables use of M62 tube system
	ZVI-Polarizer_FLDR_i90B Article no.: 11167410	Polarization filter for Falcon illumination FLDR-i90B
	ZVI-Polarizer_holder_FLDR_i90B Article no.: 11167411	Mounting adapter for polarization filter for Falcon FLDR-i90B illuminations: ZVI-Polarizer_FLDR-i90B (11167410) incl. screws
	ZVI-FLDR_i90B_DP_Diffuser A1_421 Article no.: 11167413	Diffusor with drilling holes and screws for Falcon illumination FLDR-i90B
	Multi headed cable Type A4 Split cable for illumination Article no.: 11207774	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera, 1x M8/4-pin male connector to power the I/Os and illuminations and 4x M8/4-pin female connectors for four illuminations Separate powering of camera and illumination. Double version of Output 1. Protection class IP65/IP67 Length 40 cm (M12/12-pin cable 20 cm, M8 cables 20 cm)
	Multi headed cable Type B1 Split cable for illumination Article no.: 11214470	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 1x M8/3-pin female connector for one illumination The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type B2 Split cable for illumination Article no.: 11214471	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 2x M8/3-pin female connectors for two illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type B4 Split cable for illumination Article no.: 11207776	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 4x M8/3-pin female connectors for four illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 20 cm, M8 cables 80 cm)
	Multi headed cable Type C4 Split cable for illumination Article no.: 11207777	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera, I/Os and illuminations; enable hardware trigger via input) and 4x M8/3-pin female connectors for four illuminations The I/O voltage is distributed to the illuminations through the camera as a normal trigger signal using the cameras power output. Protection class IP65/IP67 Length: 40 cm (M12/12-pin cable 20 cm, M8 cables 20 cm)
	Multi headed cable Type E1 Split cable for illumination Article no.: 11701467	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 1x M8/4-pin female connector for one illumination The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type E2 Split cable for illumination Article no.: 11701465	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 2x M8/4-pin female connectors for two illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type E4 Split cable for illumination Article no.: 11701466	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 4x M8/4-pin female connectors for four illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 20 cm, M8 cables 80 cm)

Illumination

	FFPR-i100-W Article no.: 11086540	flashable LED dark field illumination white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 100 mm
	FLDL-i150x15-W Article no.: 11086539	flashable LED bar light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 158 mm × 17 mm × 20 mm housing
	FLDL-TP-Si200x100-W Article no.: 11086537	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 116 mm × 228 mm × 23,5 mm housing
	FLDL-TP-Si36-W Article no.: 11086536	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 47 mm × 47 mm × 15 mm housing
	FLDL-TP-Si85x77-W Article no.: 11086538	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 95 mm × 95 mm × 15 mm housing
	FLDM-i100-W Article no.: 11086541	flashable LED dome light white 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 130 mm
	FLDR-i90B-IR24 Article no.: 11090900	flashable LED ring light IR 875 nm 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLDR-i90B-SR24 Article no.: 11154321	flashable LED ring light red (626 nm) 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLDR-i90B-W Article no.: 11085869	flashable LED ring light white 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLFL-Si60-IR24 Article no.: 11095910	flashable LED back light NIR diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 94 mm × 94 mm × 10 mm housing
	ZVI-FLDL-i86x15-W Article no.: 11197768	flashable LED bar light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m dimensions: 18 mm × 95 mm × 20 mm housing
	ZVI-LED Spot5WFL-B/SPS-220 Article no.: 11175036	LED spot light blue 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-Adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-IR850/SPS-220 Article no.: 11175035	LED spot light infrared 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-Adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-R/SPS-220 Article no.: 11175034	LED spot light red 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-adapter cable (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-W/SPS-220 Article no.: 11175031	LED spot light white 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-ARCUSM_24VDC_WEIß_120° ARCUS-M white 24VDC with M8 connector Article no.: 11130183	flashable LED dark field illumination white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 120 mm
	ZVI-HILIGHT120_24VDC_WEIß HI-LIGHT-120 white 24VDC with M8 connector Article no.: 11130182	flashable LED back light white diffuse radiation angle 120° diameter: 94 mm 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 127 mm × 127 mm × 20 mm housing
	ZVI-HILIGHT80_24VDC_WEIß HI-LIGHT-80 white 24VDC with M8 connector Article no.: 11130181	flashable LED back light white diffuse radiation angle 80° diameter: 94 mm 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector dimensions: 87 mm × 87 mm × 20 mm housing
	ZVI-LOGO2_24VDC_ROT617NM_30° LOGO-2 red 617nm 30° 24VDC with M8 connector Article no.: 11130184	flashable LED bar light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 74 mm × 15 mm × 17 mm housing
	ZVI-HELIOS-130_IP65_weiß_80°_24VDC_M8 HELIOS-130 IP65 white 80° 24VDC with M8 connector Article no.: 11701627	flashable LED ring light white radiation angle 80° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 134 mm IP65 protection
	ZVI-RONDOLX_24VDC_IR850NM_120° RONDO-LX IR 850nm 120° 24VDC with M8 connector Article no.: 11130150	flashable LED ring light infrared (850 nm) radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-RONDOLX_24VDC_IR850NM_50° RONDO-LX IR 850nm 50° 24VDC with M8 connector Article no.: 11130176	flashable LED ring light infrared (850 nm) radiation angle 50° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-RONDOLX_24VDC_WEIß_120° RONDO-LX white 120° 24VDC with M8 connector Article no.: 11130179	flashable LED ring light white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-TOPLIGHT80_24VDC_rot617nm_30° TOPLIGHT80 red 617nm 30° 24VDC Article no.: 11135012	flashable LED incident light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 87 mm × 87 mm × 20 mm housing
	ZVI-TOPLINED1_24VDC_ROT617NM_30° TOP-LINE-D1 red 617nm 30° 24VDC M8 1-canal Article no.: 11130187	flashable LED bar light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing
	ZVI-TOPLINED1_24VDC_SHWEIß_120° TOP-LINE-D1 SH white 120° 24VDC M8 1-canal Article no.: 11130186	flashable LED bar light SH white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing
	ZVI-TOPLINED1_24VDC_WEIß_120° TOP-LINE-D1 white 120° 24VDC M8 1-canal Article no.: 11130185	flashable LED bar light white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing