VCXG-13M.I.XT

Article no.: 11188957

1280 x 1024 px
onsemi PYTHON1300
1/2" CMOS
94 fps
Gigabit Ethernet

available on request

Technical data

show all

Sensor information

Sensor

onsemi PYTHON1300

Mono/Color

Mono

Sensor type

1/2″ CMOS

Shutter type

Global shutter

Resolution

1280 × 1024 px

Pixel size

4.8 × 4.8 µm

Exposure time

0.02 … 1000 ms

Data quality (EMVA 1288 typical)

Dark noise

9.92 e-

Saturation capacity

7619 e-

Dynamic range

57 dB

Signal-to-noise ratio

38.8 dB

Quantum efficiency

54.6 % @ 536 nm

Acquisition formats

Image formats, interface frame rate max.

Full Frame, 1280 × 1024 px, max. 94 fps
Binning 2×2, 640 × 512 px, max. 148 fps
Binning 2×1, 640 × 1024 px, max. 148 fps
Binning 1×2, 1280 × 512 px, max. 148 fps

Image formats, aquisition frame rate max. (Burst Mode)

Full Frame, 1280 × 1024 px, max. 146 fps

Pixel formats

Mono8
Mono10

Image preprocessing

Analog controls

Gain (0 … 8 dB)
Offset (0 … 63 LSB 10 Bit)

Color models

Mono

Camera features

Basic Functions

Exposure
Gain
Trigger / Exposure Active (Flash)
Binning 2x2
Partial Scan
Offset
Free Running Mode (Live Image)

Auto Functions

Exposure Auto
Gain Auto

Image Pre-processing

Image Flipping (X/Y)
LUT / Gamma

Acquisition / Interface

Burst Mode
Adjustable Framerate
Short Exposure Time Enable
Device Link Throughput Limit
Internal Image Buffer

Synchronization

free running
trigger

Trigger sources

Hardware
Software
ActionCommand

Trigger delay

0 … 2 s, tracking and buffering of up to 256 trigger signals

Process Synchronization

Events
Timer
Trigger Delay
Debouncer
Counter
Sequencer
Trigger via Action CMD (GigE)
Additional Output Modes (e.g. Trigger Ready)
PWM (PWM Duration / PWM Duty Cycle)
4 power outputs with up to 120 W (max. 48 V / 2.5 A)
Selectable Output format (e.g. Tri State, Push Pull)
Chunk data inside transferred image
Encoder support via Counter End trigger source

Additional Functions

User Set
Integrated temperature sensor
Readable additional information (e.g. sensor information)

Calibration data

Customer data storage (128 bytes user defined)

Internal image buffer

60 MB
16 images (Trigger Mode)
1 image (Free Running Mode)

Interfaces and connectors

Data interface

Gigabit Ethernet, Transfer rate 1000 Mbits/sec, Fast Ethernet, Transfer rate 100 Mbits/sec, Connector: M12 / 8 pol x-coded, screwable type

Process interface

M12 / 12 pins a-coded (SACC-CI-M12MS-12CON-L180)

Power supply

via M12/12 pins a-coded or Power over Ethernet (PoE)

Mechanical data

Lens mount

C-mount

Width

40 mm

Height

40 mm

Depth

50.8 mm

Weight

≤ 137 g

Material

aluminum, hard-anodized

Electrical data

Voltage supply range +Vs

12 … 24 V DC (external power supply)
36 … 57 V DC (Power over Ethernet)

Power consumption

Approx. 2.4 W @ 12 VDC and 94 fps
Approx. 3.1 W @ 48 VDC (PoE) and 94 fps

Non-volatile memory

Flash memory size

128 kB

Environmental conditions

Operating temperature

-40 ... +70 °C @ T = measurement point

Storage temperature

-40 … +70 °C

Humidity

10 … 90 % (non-condensing)

Protection class

IP 40 (with mounted lens and cable)
IP 54 (with mounted lens and cable)
IP 65 (with mounted tube and cable)
IP 67 (with mounted tube and cable)
IP 69K (with stainless steel housing accessory)

Digital I/Os

Lines

4 input lines
4 power output lines with pulse width modulation (PWM) (max. 48 V / max. 2,5 A)

Conformity

Conformity

CE
RoHS
UL recognized
EAC

Software

show all

Software packages

Baumer neoAPI (Windows, Linux, Linux ARM)
- Link
Baumer Camera Explorer (Windows, Linux, Linux ARM)
- Link
Baumer GAPI SDK v2.x (Windows, Linux, Linux ARM)
- Link
Baumer GAPI software examples
- Link
Third Party Software
- Link

Software

Baumer IPConfig Tool v2.0.2 (Windows)
- EN (zip | 5 MB)

Downloads

show all

Data sheet

Data sheet – VCXG-13M.I.XT
- DE (pdf | 1 MB)
Data sheet – VCXG-13M.I.XT
- EN (pdf | 1 MB)
Detailed data sheet – VCXG-13M.I.XT
- EN (pdf | 549 KB)

Quickstart

Quick Start Guide VCXG.I
- EN (pdf | 1 MB)

Operating Manual

User’s Guide VCXG / VCXG.I / VCXU cameras
- EN (pdf | 11 MB)

Certificates / approvals

CE certification
- EN/DE/BG/CZ/DK/ES/FI/FR/GR/HU/IT/LT/LV/NL/NO/PL/PT/RO/SK/SI (pdf | 280 KB)
UL certification
- EN (pdf | 506 KB)

Additional information

EMVA 1288 Summary Sheet
- EN (pdf | 227 KB)
Compliant list for Baumer industrial cameras (GigE)
- EN (pdf | 882 KB)

Application notes

Application Notes
- Link

CAD

VCXG-13M.I.XT / STEP
- (zip | 532 KB)

EPLAN

Link to dataportal
- Link to Data Portal

Drawings

show all

Dimension drawing

The selected altAttribute does not exist!

(png | 119 KB)

Schematic diagram

(png | 379 KB)

(png | 252 KB)

(png | 159 KB)

Accessories

show all

Power supply

Power Supply 24V/1.0A Int. DC Connector

Article no.: 11079750

power supply 24V/1,0A with adapters for EU, US, UK AU, KR
in combination with "Cable power adapter M12/DC connector" (11048083) suitable for VCXG.I(.XT), VLXT, VAX and VeriSens

Starter Kit

VCXG.I Starter Kit

Article no.: 11190348

GigE PCIe interface board
GigE cable 5,0 m (M12/x-coded)
Power Supply 24 V/1.0 A with adapter cable M12/12-pin to DC connector
Mounting Adapter Type B (Tripod)
Tube system M47 with adapter (11185373) and tube (11185370)
camera not included

PCIe/Adapter

	PCIe Ethernet Server Adapter I210 Article no.: 11137188	Gigabit Ethernet network adapter PCIe x1 (single lane) server adapter single GigE port supports screw lock connectors
	ZVA-Intel_Eth_Serv Adaptr_I350-T2V2 Article no.: 11168452	Gigabit Ethernet network adapter PCIe x2 (dual lane) server adapter single GigE port
	ZVA-PCIe-1672E-AE Article no.: 11168453	Gigabit Ethernet interface board PCIe x4 (quad lane) Dual GigE port Note: 4 lane PCI Express connector required

Housing accessories

	Tube Adapter A M47 hard anodized Article no.: 11185373	adapter to mount the Tube M47 hard anodized (11185370/11195425) to VCXG.I and VAX cameras thread: M47 length 2 mm
	Tube M47 hard anodized Article no.: 11185370	hard anodized lens protection with M47 thread optional tube extension with Tube Module 6mm (11185372) or Tube Module (11185371), length 12 mm. Use of several Tube Modules possible. thread: M47 length 44 mm
	Tube M47 hard anodized L12 Article no.: 11702640	hard anodized lens protection with M47 thread optional tube extension with Tube Module 6mm (11185372) or Tube Module (11185371), length 12 mm. Use of several Tube Modules possible. thread: M47 length 12 mm
	Tube M47 hard anod. scratchproof glass Article no.: 11701124	hard anodized lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (Generation 3) optional tube extension with Tube Module 6mm (11185372) or Tube Module (11185371), length 12 mm. Use of several Tube Modules possible. thread: M47 length 44 mm
	Tube Module 6 mm M47 hard anodized Article no.: 11185372	modular extension of the lens protection thread: M47 length 6 mm
	Tube Module 12 mm M47 hard anodized Article no.: 11185371	modular extension of the lens protection thread: M47 length 12 mm
	Tube Module 36 mm M47 hard anodized Article no.: 11211571	modular extension of the lens protection thread: M47 length 36 mm
	Tube Adapter B M62 hard anodized Article no.: 11185377	adapter to mount the Tube M62 hard anodized (11185374/11701125) to VCXG.I and VAX cameras thread: M62 length 2 mm
	Housing base set A VCXG.I r IP65/67 HA Article no.: 11207845	Hard anodized cylindric housing corpus for VCXG.I cameras for modular housing to meet Parma and Food & Beverage applications requirements optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). thread: M62 length 56 mm
	Tube M62 hard anodized Article no.: 11185374	hard anodized lens protection with M62 thread optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube M62 hard anod. scratchproof glass Article no.: 11701125	hard anodized lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (generation 3) optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube Module 6 mm M62 hard anodized Article no.: 11185376	modular extension of the lens protection thread: M62 length 6 mm
	Tube Module 12 mm M62 hard anodized Article no.: 11185375	modular extension of the lens protection thread: M62 length 12 mm
	Tube Module 36 mm M62 hard anodized Article no.: 11198906	modular extension of the lens protection thread: M62 length 36 mm
	Tube Adapter D M92 hard anodized Article no.: 11704311	adapter to mount the Tube M92 hard anodized (11704312) to VCX.I and VAX cameras thread: M92 length 2 mm
	Tube M92 hard anodized PMMA Article no.: 11704312	hard anodized lens protection with M92 thread optional tube extension with Tube Module 6mm (11704395) or Tube Module (11704397), length 12 mm. Use of several Tube Modules possible. thread: M92 length 70 mm
	Tube Module 6 mm M92 hard anodized Article no.: 11704395	modular extension of the lens protection thread: M92 length 6 mm
	Tube Module 12 mm M92 hard anodized Article no.: 11704397	modular extension of the lens protection thread: M92 length 12 mm
	Tube Module 36 mm M92 hard anodized Article no.: 11704394	modular extension of the lens protection thread: M92 length 36 mm
	Housing base set C V4A VCXG.I r IP65/67 Article no.: 11704019	Stainless steel cylindric housing corpus to modularly house VCXG.I cameras, IP65/57 protection for Pharma as well as Food & Beverage applications Optional: M62 Tube extension with Tube Module 6 mm M62 V4A (11704016), Tube Module 12 mm M62 V4A (11704015) or Tube Module 36 mm M62 V4A (11704014). Use of several tube modules possible. Rear side prepared for mounting via DN50 clamp tube thread: M62 length 90,5 mm To be ordered separately: stainless steel lens protection Tube M62 V4A PMMA (11704017) necessary to close the housing
	Tube M62 V4A PMMA Article no.: 11704017	stainless steel lens protection with PMMA cover glass (FDA certified) suitable for Housing base set C V4A VCXG.I r IP65/67 thread: M62 length 58 mm
	Tube M62 V4A scratchproof glass Article no.: 11704018	stainless steel lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (generation 3) optional tube extension with Tube Module 6mm M62 V4A (11704016), Tube Module 12 mm M62 V4A (11704015) or Tube Module 36 mm M62 V4A (11704015). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube Module 6 mm M62 V4A Article no.: 11704016	modular extension of the lens protection (for Housing base set C V4A VCXG.I r IP65/67) material: stainless steel thread: M62 length 6 mm
	Tube Module 12 mm M62 V4A Article no.: 11704015	modular extension of the lens protection (for Housing base set C V4A VCXG.I r IP65/67) material: stainless steel thread: M62 length 12 mm
	Tube Module 36 mm M62 V4A Article no.: 11704014	modular extension of the lens protection (for Housing base set C V4A VCXG.I r IP65/67) material: stainless steel thread: M62 length 36 mm
	Housing base set B V4A VCXG.I r IP69K Article no.: 11207844	Stainless steel housing base set for Pharma and Food & Beverage applications (incl. Splash and food zones) Hygienic design (design according to EHEDG guidelines) to house VCXG.I cameras, IP69K protection Housing corpus with clamp elements to position the chosen VCXG.I camera M40 hygienic gland and M40 stainless steel counter nut to for fixation at the machine wall sealed up cable gland for IP68 protection inside the machine To be ordered separately: stainless steel lens protection Tube M60 V4A IP69K (11208732) necessary to close the housing
	Housing V4A IP69K Mounting Tool Article no.: 11208719	Mounting tool to seal the stainless steel V4A VCXG.I r IP69K housing system
	Tube M60 V4A IP69K Acryl Article no.: 11208732	stainless steel lens protection with PMMA cover glass (FDA certified) suitable for Housing base set B V4A VCXG.I r IP69K (11208744) thread: M60 length 31 mm
	Cover Glass Replacement Acryl 2" Article no.: 11217113	Replacement cover glass for exchange in "Tube M60 V4A IP69K Acryl" (11208732) PMMA material FDA certified
	Sealing ReplacementSet Housing V4A IP69K Article no.: 11217115	Complete sealing replacement set to exchange all sealings of the stainless steel V4A VCXG.I r IP69K housing system using the "Tube M60 V4A IP69K Acryl" incl. Flouroprene XP41 sealings, TPU sealing, EPDM O-rings (inside only)
	Rotation lock M40 VA4 IP69K Article no.: 11208731	Rotation lock for Housing base set B V4A VCXG.I r IP69K (11208744) with clamping part for safe position locking

Lens accessories

	Filter CL/27 (R2) ROT PENTAX Article no.: 11006551	Ricoh color filter (red)
	Filter Pol PENTAX PL27 Article no.: 11092000	Ricoh polarization filter linear filter thread
	ZVI-FILTER POL. PL30.5 C91353 Article no.: 11175428	Ricoh polarization filter linear filter thread M30.5
	ZVI-Filter Pol. PL40.5 C91301 Article no.: 11167713	Ricoh polarization filter linear filter thread M40.5
	ZVL-Adapter S-Mount / C-Mount Article no.: 11167984	Adapter S-mount / C-mount
	ZVF-Filter Holder Mounting Tool Article no.: 11177601	Mounting tool to screw in filter holders
	Close-up ring set ZVS-FP-RGST six-piece Article no.: 11010529	Close-up ring set ZVS-FP-RGST six-piece 0,5, 1, 5, 10, 20, 40 mm

Lens

	ZVL-E3146B-R1 Article no.: 11701909	Evetar lens 5,4 mm F 2,8 format 1/2,3" M.O.D. 0,3 m IR Cut Filter S-mount
	ZVL-E3196B Article no.: 11702382	Evetar lens 7,13 mm F 2,4 format 1/2,3" M.O.D. 0,5 m S-mount
	ZVL-E3196B Article no.: 11701908	Evetar lens 12 mm F 2,0 format 1/1,8" M.O.D. 0,3 m S-mount
	ZVL-LM3NCM 3,5mm/f2,4 Article no.: 11116658	Kowa lens 3,5 mm F 2,4-14 format 1/1.8'' M.O.D. 0,1 m C-mount
	Obj Kowa LM8JCM 8mm/f1,4 Article no.: 11092788	Kowa lens 8 mm F 1,4 format 2/3" M.O.D. 0,1 m C-mount
	ZVL-FL-CC0614A-2M Article no.: 11150221	Ricoh Imaging lens 6 mm F 1,4-16 format 1/2" M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-FL-CC0814A-2M Article no.: 11150223	Ricoh Imaging lens 8 mm F 1,4-16 format 2/3" M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-FL-CC1214A-2M Article no.: 11150226	Ricoh Imaging lens 12 mm F 1,4-16 format 2/3" M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-FL-CC1614A-2M Article no.: 11150228	Ricoh Imaging lens 16 mm F 1,4-16 format 2/3" M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-FL-CC2514A-2M Article no.: 11150229	Ricoh Imaging lens 25 mm F 1,4-16 format 2/3" M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-FL-CC5024A-2M Article no.: 11150230	Ricoh Imaging lens 50 mm F 2,4-22 format 2/3" M.O.D. 0,3 m locating screw for aperture and focus C-mount
	ZVL-FL-HC0614-2M Article no.: 11008992	Ricoh Imaging lens 6 mm F 1,4-16 format 1/2" M.O.D. 0,1 m locating screw for aperture and focus C-mount
	ZVL-FL-HC1214-2M Article no.: 11004362	Ricoh Imaging lens 12 mm F 1,4-16 format 1/2" M.O.D. 0,25 m locating screw for aperture and focus C-mount
	ZVL-FL-CC1614-2M Article no.: 10170039	Ricoh Imaging lens 16 mm F 1,4-16 format 2/3" M.O.D. 0,25 m locating screw for aperture and focus C-mount
	ZVL-FL-CC2514-2M Article no.: 11002222	Ricoh Imaging lens 25 mm F 1,4-16 format 2/3" M.O.D. 0,25 m locating screw for aperture and focus C-mount
	ZVL-FL-CC3516-2M Article no.: 11003417	Ricoh Imaging lens 35 mm F 1,6-16 format 2/3" M.O.D. 0,35 m locating screw for aperture and focus C-mount
	ZVL-FL-CC5028-2M Article no.: 11012785	Ricoh Imaging lens 50 mm F 2,8-22 format 2/3" M.O.D. 0,9 m locating screw for aperture and focus C-mount
	ZVL-FL-CC7528-2M Article no.: 11003041	Ricoh Imaging lens 75 mm F 2,8 32 format 2/3" M.O.D. 0,7 m locating screw for aperture and focus C-mount

Network components

GigE Power Switch

Article no.: 11008795

GigE switch
PoE and Jumbo Frame support
4x 1000base-T
DIN rail mounting
operating voltage: 24-48 V; PoE requires 48 V

Cable

	CAM12.X8-11230367 Article no.: 11230367	M12, male, X-coded, 8-poles; PUR, 500 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230493 Article no.: 11230493	M12, male, X-coded, 8-poles; PUR, 1000 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230494 Article no.: 11230494	M12, male, X-coded, 8-poles; PUR, 1500 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230495 Article no.: 11230495	M12, male, X-coded, 8-poles; PUR, 2000 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	Cable GigE M12X/RJ45, STP 2.0m, flex Article no.: 11185139	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 2,0 m
	Cable GigE M12X/RJ45, STP 5.0m, flex Article no.: 11195760	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 5,0 m
	Cable GigE M12X/RJ45, STP 10.0m, flex Article no.: 11195761	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 10,0 m
	Cable GigE M12X/RJ45, STP 15.0m, flex Article no.: 11195762	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 15,0 m
	Cable GigE M12X/RJ45, STP 20.0m, flex Article no.: 11196995	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 20,0 m
	Cable GigE M12X/RJ45, STP, 2.0m, flex, 90° Article no.: 11195125	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic apllications (+/- 180°/0,5m, min. 1.000.000 torsion cycles) length 2,0 m
	Cable GigE M12X/RJ45, STP, 5.0m, flex, 90° Article no.: 11195123	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 5,0 m
	Cable GigE M12X/RJ45, STP, 10.0m, flex, 90° Article no.: 11195122	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 10,0 m
	Cable GigE M12X/RJ45, STP, 20.0m, flex, 90° Article no.: 11195121	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 20,0 m
	Cable GigE M12X/RJ45, STP, 30.0m, flex, 90° Article no.: 11195120	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 30,0 m
	Cable GigE M12X/RJ45, STP 30.0m, flex Article no.: 11185190	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 30,0 m
	Adapter Cable TX to VCXG.I VLXT Adapter Cable Article no.: 11701126	Adapter to connect VCXG.I or VLXT cameras to existing TXG cabling Split cable M12/12-pin male connector to 1x M8/3-pin female connector (power) and 1x M8/4-pin female connector (I/Os) Protection class IP65/IP67 Length 0.4 m
	Cable Power Adapter M12/DC Connector Article no.: 11048083	shielded adapter connection cable M12/12-pin male connector to confectioned DC connector length 2,0 m manufactured cable: 11201118 ESG 34JP0200GS
	ESG 34JP0200GS Shielded cable 12 wires, female connector, 2,0 m Article no.: 11201118	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESG 34JP0500GS Shielded cable 12 wires, female connector, 5,0 m Article no.: 11195097	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESG 34JP1000GS Shielded cable 12 wires, female connector, 10,0 m Article no.: 11195098	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESG 34JP2000GS Shielded cable 12 wires, female connector, 20,0 m Article no.: 11195099	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 20,0 m
	ESW 33JP0200GS 90° shielded cable 12 wires, female connector, 2,0 m Article no.: 11201128	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESW 33JP0500GS 90° shielded cable 12 wires, female connector, 5,0 m Article no.: 11195094	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESW 33JP1000GS 90° shielded cable 12 wires, female connector, 10,0 m Article no.: 11195095	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESW 33JP2000GS 90° shielded cable 12 wires, female connector, 20,0 m Article no.: 11195096	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 20,0 m

Mountings and heat sinks

	Mounting Adapter Type D (Front) Article no.: 11165176	mounting adapter for VCXU, VCXG and VCXG.I cameras incl. screw (hexagon socket) stable front side mounting
	Mounting Adapter Type A (Front) Article no.: 11002638	camera mounting adapter for TX, PX, VCXG.I and VisiLine cameras incl. screws (hexagon socket) and washers stable front side mounting
	Mounting Adapter Type B (Tripod) Article no.: 11003060	camera mounting adapter for TX, VisiLine, VisiLine IP, VCXG.I, LXG, LXC, PX and SX/HX cameras incl. screws (hexagon socket) and washers stable bottom and tripod mounting
	Mounting Adapter Type C Article no.: 11053252	camera mounting adapter for TX, VisiLine, VisiLine IP, VCXG.I, LX and HX cameras incl. screws (hexagon socket) and washers stable sidewise mounting

Illumination accessories

	ZVI-CONNECT_CameraExtension_CX.I_Type1 Article no.: 11701629	mounting adapter for illuminations Rondo LX and HELIOS-130 to VCXG.I cameras enables use of M62 tube system
	ZVI-Polarizer_FLDR_i90B Article no.: 11167410	Polarization filter for Falcon illumination FLDR-i90B
	ZVI-Polarizer_holder_FLDR_i90B Article no.: 11167411	Mounting adapter for polarization filter for Falcon FLDR-i90B illuminations: ZVI-Polarizer_FLDR-i90B (11167410) incl. screws
	ZVI-FLDR_i90B_DP_Diffuser A1_421 Article no.: 11167413	Diffusor with drilling holes and screws for Falcon illumination FLDR-i90B
	Multi headed cable Type A4 Split cable for illumination Article no.: 11207774	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera, 1x M8/4-pin male connector to power the I/Os and illuminations and 4x M8/4-pin female connectors for four illuminations Separate powering of camera and illumination. Double version of Output 1. Protection class IP65/IP67 Length 40 cm (M12/12-pin cable 20 cm, M8 cables 20 cm)
	Multi headed cable Type B1 Split cable for illumination Article no.: 11214470	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 1x M8/3-pin female connector for one illumination The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type B2 Split cable for illumination Article no.: 11214471	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 2x M8/3-pin female connectors for two illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type B4 Split cable for illumination Article no.: 11207776	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 4x M8/3-pin female connectors for four illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 20 cm, M8 cables 80 cm)
	Multi headed cable Type C4 Split cable for illumination Article no.: 11207777	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera, I/Os and illuminations; enable hardware trigger via input) and 4x M8/3-pin female connectors for four illuminations The I/O voltage is distributed to the illuminations through the camera as a normal trigger signal using the cameras power output. Protection class IP65/IP67 Length: 40 cm (M12/12-pin cable 20 cm, M8 cables 20 cm)
	Multi headed cable Type E1 Split cable for illumination Article no.: 11701467	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 1x M8/4-pin female connector for one illumination The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type E2 Split cable for illumination Article no.: 11701465	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 2x M8/4-pin female connectors for two illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type E4 Split cable for illumination Article no.: 11701466	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 4x M8/4-pin female connectors for four illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 20 cm, M8 cables 80 cm)

Illumination

	FFPR-i100-W Article no.: 11086540	flashable LED dark field illumination white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 100 mm
	FLDL-i150x15-W Article no.: 11086539	flashable LED bar light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 158 mm × 17 mm × 20 mm housing
	FLDL-TP-Si200x100-W Article no.: 11086537	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 116 mm × 228 mm × 23,5 mm housing
	FLDL-TP-Si36-W Article no.: 11086536	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 47 mm × 47 mm × 15 mm housing
	FLDL-TP-Si85x77-W Article no.: 11086538	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 95 mm × 95 mm × 15 mm housing
	FLDM-i100-W Article no.: 11086541	flashable LED dome light white 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 130 mm
	FLDR-i90B-IR24 Article no.: 11090900	flashable LED ring light IR 875 nm 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLDR-i90B-SR24 Article no.: 11154321	flashable LED ring light red (626 nm) 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLDR-i90B-W Article no.: 11085869	flashable LED ring light white 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLFL-Si60-IR24 Article no.: 11095910	flashable LED back light NIR diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 94 mm × 94 mm × 10 mm housing
	ZVI-FLDL-i86x15-W Article no.: 11197768	flashable LED bar light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m dimensions: 18 mm × 95 mm × 20 mm housing
	ZVI-LED Spot5WFL-B/SPS-220 Article no.: 11175036	LED spot light blue 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-Adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-IR850/SPS-220 Article no.: 11175035	LED spot light infrared 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-Adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-R/SPS-220 Article no.: 11175034	LED spot light red 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-adapter cable (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-W/SPS-220 Article no.: 11175031	LED spot light white 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-ARCUSM_24VDC_WEIß_120° ARCUS-M white 24VDC with M8 connector Article no.: 11130183	flashable LED dark field illumination white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 120 mm
	ZVI-HILIGHT120_24VDC_WEIß HI-LIGHT-120 white 24VDC with M8 connector Article no.: 11130182	flashable LED back light white diffuse radiation angle 120° diameter: 94 mm 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 127 mm × 127 mm × 20 mm housing
	ZVI-HILIGHT80_24VDC_WEIß HI-LIGHT-80 white 24VDC with M8 connector Article no.: 11130181	flashable LED back light white diffuse radiation angle 80° diameter: 94 mm 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector dimensions: 87 mm × 87 mm × 20 mm housing
	ZVI-LOGO2_24VDC_ROT617NM_30° LOGO-2 red 617nm 30° 24VDC with M8 connector Article no.: 11130184	flashable LED bar light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 74 mm × 15 mm × 17 mm housing
	ZVI-HELIOS-130_IP65_weiß_80°_24VDC_M8 HELIOS-130 IP65 white 80° 24VDC with M8 connector Article no.: 11701627	flashable LED ring light white radiation angle 80° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 134 mm IP65 protection
	ZVI-RONDOLX_24VDC_IR850NM_120° RONDO-LX IR 850nm 120° 24VDC with M8 connector Article no.: 11130150	flashable LED ring light infrared (850 nm) radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-RONDOLX_24VDC_IR850NM_50° RONDO-LX IR 850nm 50° 24VDC with M8 connector Article no.: 11130176	flashable LED ring light infrared (850 nm) radiation angle 50° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-RONDOLX_24VDC_WEIß_120° RONDO-LX white 120° 24VDC with M8 connector Article no.: 11130179	flashable LED ring light white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-TOPLIGHT80_24VDC_rot617nm_30° TOPLIGHT80 red 617nm 30° 24VDC Article no.: 11135012	flashable LED incident light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 87 mm × 87 mm × 20 mm housing
	ZVI-TOPLINED1_24VDC_ROT617NM_30° TOP-LINE-D1 red 617nm 30° 24VDC M8 1-canal Article no.: 11130187	flashable LED bar light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing
	ZVI-TOPLINED1_24VDC_SHWEIß_120° TOP-LINE-D1 SH white 120° 24VDC M8 1-canal Article no.: 11130186	flashable LED bar light SH white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing
	ZVI-TOPLINED1_24VDC_WEIß_120° TOP-LINE-D1 white 120° 24VDC M8 1-canal Article no.: 11130185	flashable LED bar light white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing