2. Panoramica dei prodotti
  3. Encoder / sensori angolari
  4. Encoder incrementali per l’industria
  5. Per aree Ex
  6. ExEIL580-SY
Dati tecnici
Dati tecnici - Valori elettrici
Tensione operativa
  • 5 VDC ±5 %
  • 8...30 VDC
  • 4.75...30 VDC
Reverse polarity protection
  • Yes
Short-circuit proof
  • Yes (HTL)
  • Yes (TTL, max. 1 s and 1 signal)
Corrente operativa senza carico
  • ≤70 mA
Impulsi per giro
  • 100 … 5000
Sfasamento
  • 90 ° ±10°
Rapporto ciclico
  • 40…60 %
Segnale di riferimento
  • Zero pulse, width 90° ±10 %
Principio di scansione
  • Ottico
Frequenza di uscita
  • ≤300 kHz (TTL)
  • ≤160 kHz (HTL)
Segnale di uscita
  • A+, B+, R+, A-, B-, R-
Livelli di uscita
  • TTL/RS422
  • HTL/push-pull
Immunità alle interferenze
  • EN 61000-6-2
Emissione di interferenze
  • EN 61000-6-3
Dati tecnici - progettazione meccanica
Grandezza (flangia)
  • ø58 mm
Tipo di albero
  • ø6 x 10 mm, solid shaft with flat
Carico dell‘albero massimo ammesso
  • ≤40 N assiale
  • ≤80 N radiale
Flangia
  • Synchro flange
Classe di protezione EN 60529
  • IP 65
Velocità operativa
  • ≤12000 rpm (+20 °C)
  • ≤11000 rpm (+40 °C)
  • ≤8000 rpm (+60 °C)
Coppia di spunto
  • ≤0,015 Nm (+20 °C)
Materiale
  • Alloggiamento: lega pressofusa di alluminio
  • Flange: aluminium
  • Albero: acciaio inox
Ambient temperature
  • -20...+60 °C
Relative humidity
  • 90 % non-condensing
Resistenza
  • EN 60068-2-6
  • Vibrazione 30 g, 10-2000 Hz
  • EN 60068-2-27
  • Urti 300 g, 6 ms
Protezione da esplosione
  • II 3 D Ex tc IIIC T135°C Dc X (dust): see special conditions “X”
Allacciamento
  • Flange connector M12, 8-pin
  • Flange connector M23, 12-pin
  • Cavo
Peso ca.
  • 300 g
Scaricare
Data sheet
Quickstart
Brochures / Catalogs
Declaration of conformity
CAD

  • EIL580: Synchro flange (flute ø53 mm), solid shaft ø6 mm, cable axial, IP65 / STEP (EIL580-SY06.5Tx.xxxxx.A)

  • EIL580: Synchro flange (flute ø53 mm), solid shaft ø6 mm, cable radial, IP65 / STEP (EIL580-SY06.5Rx.xxxxx.A)

  • EIL580: Synchro flange (flute ø53 mm), solid shaft ø6 mm, cable tangential, IP65 / STEP (EIL580-SY06.5Px.xxxxx.A)

  • EIL580: Synchro flange (flute ø53 mm), solid shaft ø6 mm, connector M12 axial, IP65 / STEP (EIL580-SY06.5Ax.xxxxx.A)

  • EIL580: Synchro flange (flute ø53 mm), solid shaft ø6 mm, connector M12 radial, IP65 / STEP (EIL580-SY06.5Bx.xxxxx.A)

  • EIL580: Synchro flange (flute ø53 mm), solid shaft ø6 mm, connector M23 axial, IP65 / STEP (EIL580-SY06.5Dx.xxxxx.A)

  • EIL580: Synchro flange (flute ø53 mm), solid shaft ø6 mm, connector M23 radial, IP65 / STEP (EIL580-SY06.5Fx.xxxxx.A)

Accessori
Accessori di montaggio
The selected altAttribute does not exist! Coupling CPS25 (L=19, D1=06 / D2=06)
For encoder with solid shaft

Articolo n..: 11065916
  • Precision coupling
  • Torsionally stiff coupling with low installation depth
  • Pluggable
  • Electrically insulating center disk
  • Suitable for very high speeds
The selected altAttribute does not exist! Coupling CPS25 (L=19, D1=06 / D2=08)
For encoder with solid shaft

Articolo n..: 11065917
  • Precision coupling
  • Torsionally stiff coupling with low installation depth
  • Pluggable
  • Electrically insulating center disk
  • Suitable for very high speeds
The selected altAttribute does not exist! Coupling CPS25 (L=19, D1=10 / D2=06)
For encoder with solid shaft

Articolo n..: 11065922
  • Precision coupling
  • Torsionally stiff coupling with low installation depth
  • Pluggable
  • Electrically insulating center disk
  • Suitable for very high speeds
The selected altAttribute does not exist! Coupling CPS25 (L=19, D1=11 / D2=06)
For encoder with solid shaft

Articolo n..: 11065926
  • Precision coupling
  • Torsionally stiff coupling with low installation depth
  • Pluggable
  • Electrically insulating center disk
  • Suitable for very high speeds
The selected altAttribute does not exist! Coupling CPS25 (L=19, D1=12 / D2=06)
For encoder with solid shaft

Articolo n..: 11065928
  • Precision coupling
  • Torsionally stiff coupling with low installation depth
  • Pluggable
  • Electrically insulating center disk
  • Suitable for very high speeds
The selected altAttribute does not exist! Spring washer coupling (D1=6 / D2=6)
For encoder with solid shaft

Articolo n..: 10141131
  • Backlash-free and angle-synchronous transmission of rotary movements
  • Plug-in version
  • Electric isolated
  • Suitable for very high speeds
  • Good compensation of all misalignments
The selected altAttribute does not exist! Spring washer coupling (D1=6 / D2=10)
For encoder with solid shaft

Articolo n..: 10141132
  • Backlash-free and angle-synchronous transmission of rotary movements
  • Plug-in version
  • Electric isolated
  • Suitable for very high speeds
  • Good compensation of all misalignments
The selected altAttribute does not exist! Spring washer coupling (D1=6 / D2=16)
For encoder with solid shaft

Articolo n..: 11034139
  • Backlash-free and angle-synchronous transmission of rotary movements
  • Plug-in version
  • Electric isolated
  • Suitable for very high speeds
  • Good compensation of all misalignments
The selected altAttribute does not exist! Bellows coupling (D1=06 / D2=10)
For encoder with solid shaft

Articolo n..: 11050507
  • Backlash-free angle-synchronous transmission
  • Optimum compensation of misalignments
  • Very high torsional spring stiffness
  • Small restoring force
  • Vibration damping
  • Stainless steel bellows
The selected altAttribute does not exist! Mounting adaptor
For encoders with synchro flange

Articolo n..: 10117667
  • Glass-fiber reinforced plastic
  • Excellent resistance against temperature and chemicals
  • Electrically isolated encoder mount
The selected altAttribute does not exist! Set of eccentric fixings for mounting clamp (10117667)

Articolo n..: 10117668
  • With 3x eccentric fixings, screws and nuts
The selected altAttribute does not exist! Set of eccentric fixings type A

Articolo n..: 11065545
  • With 3 eccentric fixings type A
The selected altAttribute does not exist! Bearing flange for encoders with synchro flange (Z 119.035)

Articolo n..: 10158124
  • For all encoder with synchro flange and 6 mm shaft
  • Material: Aluminium, bare
Connettori e cavi
The selected altAttribute does not exist! Female connector M23 with pin lock, 12-pin, CW

Articolo n..: 11141051
  • Connector M23: 12-pin, female, clockwise (CW). Suitable for cable connection to flange connector M23 (12-pin, male, counter-clockwise (CCW)).
  • Knurled nut with pin lock
  • EMC version
  • Temperature range -40...+100 °C
In alto