VLXT-83UV.I

Article no.: 11725745

2848 × 2832 px
Sony IMX487
2/3″ CMOS
150 fps
10 GigE
Spectrum: UV (200–400 nm)
Firmware update required to use RDMA

available on request

Technical data

show all

Sensor information

Sensor

Sony IMX487

Mono/Color

Sensor type

2/3″ CMOS

Shutter type

Global shutter

Resolution

2848 × 2832 px

Pixel size

2.74 × 2.74 µm

Exposure time

0.001 … 60000 ms

Data quality (EMVA 1288 typical)

Dark noise

2.5 e-

Saturation capacity

9000 e-

Dynamic range

70 dB

Signal-to-noise ratio

40 dB

Quantum efficiency

39 % @ 265 nm

Acquisition formats

Image formats, interface frame rate max.

Full Frame, 2848 × 2832 px, max. 150 fps
Binning 2×2, 1424 × 1416 px, max. 172 fps
Binning 2×1, 1424 × 2832 px, max. 172 fps
Binning 1×2, 2848 × 1416 px, max. 172 fps

Image formats, aquisition frame rate max. (Burst Mode)

Full Frame, 2848 × 2832 px, max. 172 fps

Pixel formats

Mono8
Mono10
Mono12
Mono12 Packed

Image preprocessing

Analog controls

Gain (0 … 48 dB)
Offset (0 … 255 LSB 12 Bit)

Color models

Mono
Raw Bayer
RGB
BGR

Camera features

Basic Functions

Exposure
Gain / Color Gain
Trigger / Exposure Active (Flash)
Binning 2x2
Partial Scan
Offset
Free Running Mode (Live Image)
Multi ROI

Auto Functions

Exposure Auto
Gain Auto

Image Pre-processing

Image Flipping (X/Y)
LUT / Gamma
Shading Correction
Edge Sharpening
Noise Reduction

Acquisition / Interface

Burst Mode
Adjustable Framerate
Short Exposure Time Enable
Device Link Throughput Limit
Internal Image Buffer

Synchronization

free running
trigger

Trigger sources

Hardware
Software
ActionCommand

Trigger delay

0 … 2 s, tracking and buffering of up to 256 trigger signals

Process Synchronization

Events
Timer
Trigger Delay
Debouncer
Counter
Sequencer
Trigger via Action CMD (GigE)
Action CMD Request ID
Trigger ID inside Chunk
Additional Output Modes (e.g. Trigger Ready)
PWM (PWM Duration / PWM Duty Cycle)
Selectable Output format (e.g. Tri State, Push Pull)
Chunk data inside transferred image
Encoder support via Counter End trigger source
4 power outputs with up to 120 W (max. 48 V / 2.5 A)

Time synchronization IEEE 1588

IEEE 1588 / Master and Slave function
IEEE 1588 / Scheduled Action CMD
IEEE 1588 / Synchronized Acquisition Framerate

Additional Functions

User Set
Integrated temperature sensor
Readable additional information (e.g. sensor information)
Save Custom Data

Lens control

Corning liquid lens

Internal image buffer

1024 MB
127 images (Trigger Mode)
1 image (Free Running Mode)

Interfaces and connectors

Data interface

10 Gigabit Ethernet, Transfer rate 10000 Mbits/sec, Gigabit Ethernet, Transfer rate 1000 Mbits/sec, Fast Ethernet, Transfer rate 100 Mbits/sec, Connector: M12 / 8-pol x-coded (SACC-CI-M12FS-8CON-L180-10G)

Process interface

M12 / 12 pins a-coded (SACC-CI-M12MS-12CON-L180)

Power supply

via M12/12 pins a-coded

Mechanical data

Lens mount

C-mount

Width

60 mm

Height

60 mm

Depth

99.7 mm

Weight

≤ 485 g

Material

aluminum, hard-anodized

Electrical data

Voltage supply range +Vs

19.2 … 28.8 V DC (external power supply)

Power consumption

Approx. 12.7 W @ 24 VDC and 150 fps

Non-volatile memory

Flash memory size

128 kB

Environmental conditions

Operating temperature

0 … +60 ° @ T = measurement point

Humidity

0 … 90 % (non-condensing)

Protection class

IP 40
IP 54 (with mounted lens and cable)
IP 65 (with mounted tube and cable)
IP 67 (with mounted tube and cable)

Digital I/Os

Lines

2 input lines
4 power output lines with pulse width modulation (PWM) (max. 48 V / max. 2,5 A)
RS232

Output line sources

Off
Exposure Active
Timer1
Readout Active
User0
User1
User2
TriggerReady

Conformity

Conformity

CE
RoHS

Software

show all

Software packages

Baumer neoAPI (Windows, Linux, Linux ARM)
- Link
Baumer Camera Explorer (Windows, Linux, Linux ARM)
- Link
Baumer GAPI SDK v2.x (Windows, Linux, Linux ARM)
- Link
Baumer GAPI software examples
- Link
Third Party Software
- Link

Software

Baumer IPConfig Tool v2.0.2 (Windows)
- EN (zip | 5 MB)

Downloads

show all

Data sheet

Data sheet – VLXT-83UV.I
- DE (pdf | 1 MB)
Data sheet – VLXT-83UV.I
- EN (pdf | 1 MB)
Detailed data sheet – VLXT-83UV.I
- EN (pdf | 526 KB)

Quickstart

Quick Start Guide VLXT
- EN (pdf | 1 MB)

Operating Manual

User’s Guide VLXT.I / VLXT.FO cameras
- EN (pdf | 14 MB)

Certificates / approvals

UL certification
- EN (pdf | 360 KB)

Additional information

EMVA 1288 Summary Sheet
- EN (pdf | 395 KB)
Compliant list for Baumer industrial cameras (10 GigE)
- EN (pdf | 626 KB)

Application notes

Application Notes
- Link

Drawings

show all

Dimension drawing

The selected altAttribute does not exist!

(png | 109 KB)

Schematic diagram

(png | 252 KB)

Accessories

show all

Power supply

Power Supply 24V/1.0A Int. DC Connector

Article no.: 11079750

power supply 24V/1,0A with adapters for EU, US, UK AU, KR
in combination with "Cable power adapter M12/DC connector" (11048083) suitable for VCXG.I(.XT), VLXT, VAX and VeriSens

Starter Kit

VLXT Starter Kit

Article no.: 11204995

10-GigE PCIe interface board
GigE cable 5,0 m (M12/x-coded)
Power Supply 24 V/1.0 A with adapter cable M12/12-pin to DC connector
Tube system M62 with adapter (11193125) and tube (11185374)
Mounting Adapter Type C
Heat Sink Type B
camera not included

PCIe/Adapter

	ZVA-Intel_X550-T2_10GbE_Serv_Adapter Article no.: 11190893	10-GigE PCIe interface board PCIe x4 (quad lane) converged network adapter dual GigE port max. power consumption 8.4 W (10 GigE single port use) / 13.0 W (10 GigE dual port use) incl. SW driver (CD)
	PCIe Ethernet Server Adapter I210 Article no.: 11137188	Gigabit Ethernet network adapter PCIe x1 (single lane) server adapter single GigE port supports screw lock connectors
	ZVA-Intel_Eth_Serv Adaptr_I350-T2V2 Article no.: 11168452	Gigabit Ethernet network adapter PCIe x2 (dual lane) server adapter single GigE port
	ZVA-PCIe-1672E-AE Article no.: 11168453	Gigabit Ethernet interface board PCIe x4 (quad lane) Dual GigE port Note: 4 lane PCI Express connector required

Housing accessories

	Tube Adapter C M62 hard anodized Article no.: 11193125	adapter to mount the Tube M62 hard anodized (11185374/11701125) to VLXT cameras thread: M62 length 2 mm
	Tube M62 hard anodized Article no.: 11185374	hard anodized lens protection with M62 thread optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm
	Tube Module 6 mm M62 hard anodized Article no.: 11185376	modular extension of the lens protection thread: M62 length 6 mm
	Tube Module 12 mm M62 hard anodized Article no.: 11185375	modular extension of the lens protection thread: M62 length 12 mm
	Tube Module 36 mm M62 hard anodized Article no.: 11198906	modular extension of the lens protection thread: M62 length 36 mm
	Tube M62 hard anod. scratchproof glass Article no.: 11701125	hard anodized lens protection with scratchproof laminated safety glass: Corning^® Gorilla^® glass (generation 3) optional tube extension with Tube Module 6mm (11185376), Tube Module 12 mm (11185375) or Tube Module 36 mm (11198906). Use of several Tube Modules possible. thread: M62 length 58 mm

Lens accessories

	Adapter TFL-Mount / C-Mount Article no.: 11702566	Lens mount adapter from TFL-mount (camera) to C-Mount (lens)
	Filter CL/27 (R2) ROT PENTAX Article no.: 11006551	Ricoh color filter (red)
	ZVI-FILTER POL. PL30.5 C91353 Article no.: 11175428	Ricoh polarization filter linear filter thread M30.5
	ZVI-Filter Pol. PL40.5 C91301 Article no.: 11167713	Ricoh polarization filter linear filter thread M40.5
	ZVF-Filter Holder Mounting Tool Article no.: 11177601	Mounting tool to screw in filter holders

Lens

	ZVL-HF1635V-UV Article no.: 11728662	Myutron lens 16 mm F 3.5 format 1" M.O.D. 0.095 m locating screw for aperture and focus C-mount suitable for UV and visible wavelengths (190 - 700 nm)
	ZVL-HF2528V-UV Article no.: 11728663	Myutron lens 25 mm F 2.8 format 1" M.O.D. 0.091 m locating screw for aperture and focus C-mount suitable for UV and visible wavelengths (190 - 700 nm)
	ZVL-HF3535V-UV Article no.: 11728664	Myutron lens 35 mm F 3.5 format 1" M.O.D. 0.191 m locating screw for aperture and focus C-mount suitable for UV and visible wavelengths (190 - 700 nm)
	ZVL-HF5035V-UV Article no.: 11728665	Myutron lens 50 mm F 3.5 format 1" M.O.D. 0.183 m locating screw for aperture and focus C-mount suitable for UV and visible wavelengths (190 - 700 nm)

Network components

GigE Power Switch

Article no.: 11008795

GigE switch
PoE and Jumbo Frame support
4x 1000base-T
DIN rail mounting
operating voltage: 24-48 V; PoE requires 48 V

Cable

	CAM12.X8-11230367 Article no.: 11230367	M12, male, X-coded, 8-poles; PUR, 500 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230493 Article no.: 11230493	M12, male, X-coded, 8-poles; PUR, 1000 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230494 Article no.: 11230494	M12, male, X-coded, 8-poles; PUR, 1500 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	CAM12.X8-11230495 Article no.: 11230495	M12, male, X-coded, 8-poles; PUR, 2000 cm, shielded; RJ45, male, X-coded, 8-poles Dragchain capable; suitable for robotics ± 180 °/m, CAT6A, 10GBit/s Head A: IP66K, IP67; Head B: IP20 Cable: good resistance against flames, oils Halogen free
	Cable GigE M12X/RJ45, STP 2.0m, flex Article no.: 11185139	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 2,0 m
	Cable GigE M12X/RJ45, STP 5.0m, flex Article no.: 11195760	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 5,0 m
	Cable GigE M12X/RJ45, STP 10.0m, flex Article no.: 11195761	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 10,0 m
	Cable GigE M12X/RJ45, STP 15.0m, flex Article no.: 11195762	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 15,0 m
	Cable GigE M12X/RJ45, STP 20.0m, flex Article no.: 11196995	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 20,0 m
	Cable GigE M12X/RJ45, STP 30.0m, flex Article no.: 11185190	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock) to RJ45 cable carrier compatible length 30,0 m
	Cable GigE M12X/RJ45, STP, 5.0m, flex, 90° Article no.: 11195123	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 5,0 m
	Cable GigE M12X/RJ45, STP, 10.0m, flex, 90° Article no.: 11195122	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 10,0 m
	Adapter Cable TX to VCXG.I VLXT Adapter Cable Article no.: 11701126	Adapter to connect VCXG.I or VLXT cameras to existing TXG cabling Split cable M12/12-pin male connector to 1x M8/3-pin female connector (power) and 1x M8/4-pin female connector (I/Os) Protection class IP65/IP67 Length 0.4 m
	Cable Power Adapter M12/DC Connector Article no.: 11048083	shielded adapter connection cable M12/12-pin male connector to confectioned DC connector length 2,0 m manufactured cable: 11201118 ESG 34JP0200GS
	ESG 34JP0200GS Shielded cable 12 wires, female connector, 2,0 m Article no.: 11201118	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESG 34JP0500GS Shielded cable 12 wires, female connector, 5,0 m Article no.: 11195097	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESG 34JP1000GS Shielded cable 12 wires, female connector, 10,0 m Article no.: 11195098	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESG 34JP2000GS Shielded cable 12 wires, female connector, 20,0 m Article no.: 11195099	shielded process interface cable M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 20,0 m
	ESW 33JP0200GS 90° shielded cable 12 wires, female connector, 2,0 m Article no.: 11201128	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 2,0 m
	ESW 33JP0500GS 90° shielded cable 12 wires, female connector, 5,0 m Article no.: 11195094	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 5,0 m
	ESW 33JP1000GS 90° shielded cable 12 wires, female connector, 10,0 m Article no.: 11195095	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 10,0 m
	ESW 33JP2000GS 90° shielded cable 12 wires, female connector, 20,0 m Article no.: 11195096	shielded process interface cable 90° angled M12/12-pin female connector to open wires cable carrier compatible suitable for robotic applications (+/- 180°/m, min. 500.000 torsion cycles) length 20,0 m
	Cable GigE M12X/RJ45, STP, 30.0m, flex, 90° Article no.: 11195120	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 30,0 m
	Cable GigE M12X/RJ45, STP, 20.0m, flex, 90° Article no.: 11195121	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic applications (+/- 180°/ 0.5 m, min. 1.000.000 torsion cycles) length 20,0 m
	Cable GigE M12X/RJ45, STP, 2.0m, flex, 90° Article no.: 11195125	Gigabit Ethernet interface cable CAT6A M12/8-pin connector, X-coded (screw lock), 90° angled to RJ45 cable carrier compatible suitable for robotic apllications (+/- 180°/0,5m, min. 1.000.000 torsion cycles) length 2,0 m

Mountings and heat sinks

	Mounting Adapter Type C Article no.: 11053252	camera mounting adapter for TX, VisiLine, VisiLine IP, VCXG.I, LX and HX cameras incl. screws (hexagon socket) and washers stable sidewise mounting
	Mounting Adapter Type H Article no.: 11191852	camera mounting adapter for cameras of the CX, LX and QX series incl. screw (hexagon socket) rotatable mounting
	Heat Sink Type A Article no.: 11037580	heat sink for TX, VCXG.I, VisiLine, VisiLine IP, LX and HX cameras incl. screws (hexagon socket) and washers 48 mm x 33 mm x 16,5 mm
	Heat Sink Type B Article no.: 11114702	heat sink for TX, VCXG.I, VisiLine, VisiLine IP, LX and HX cameras incl. screws (hexagon socket) and washers 50 mm x 50 mm x 40 mm

Illumination accessories

	ZVI-CONNECT_CameraExtension_VLXT.I_Type1 Article no.: 11701628	mounting adapter for illuminations Rondo LX and HELIOS-130 to VLXT.I cameras enables use of M62 tube system
	ZVI-Polarizer_FLDR_i90B Article no.: 11167410	Polarization filter for Falcon illumination FLDR-i90B
	ZVI-Polarizer_holder_FLDR_i90B Article no.: 11167411	Mounting adapter for polarization filter for Falcon FLDR-i90B illuminations: ZVI-Polarizer_FLDR-i90B (11167410) incl. screws
	ZVI-FLDR_i90B_DP_Diffuser A1_421 Article no.: 11167413	Diffusor with drilling holes and screws for Falcon illumination FLDR-i90B
	Multi headed cable Type A4 Split cable for illumination Article no.: 11207774	Split cable M12/12-pin female connector to 1x M8/3-pin male connector for power the camera, 1x M8/4-pin male connector to power the I/Os and illuminations and 4x M8/4-pin female connectors for four illuminations Separate powering of camera and illumination. Double version of Output 1. Protection class IP65/IP67 Length 40 cm (M12/12-pin cable 20 cm, M8 cables 20 cm)
	Multi headed cable Type B1 Split cable for illumination Article no.: 11214470	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 1x M8/3-pin female connector for one illumination The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type B2 Split cable for illumination Article no.: 11214471	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 2x M8/3-pin female connectors for two illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type B4 Split cable for illumination Article no.: 11207776	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 4x M8/3-pin female connectors for four illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 20 cm, M8 cables 80 cm)
	Multi headed cable Type C4 Split cable for illumination Article no.: 11207777	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera, I/Os and illuminations; enable hardware trigger via input) and 4x M8/3-pin female connectors for four illuminations The I/O voltage is distributed to the illuminations through the camera as a normal trigger signal using the cameras power output. Protection class IP65/IP67 Length: 40 cm (M12/12-pin cable 20 cm, M8 cables 20 cm)
	Multi headed cable Type E1 Split cable for illumination Article no.: 11701467	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 1x M8/4-pin female connector for one illumination The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type E2 Split cable for illumination Article no.: 11701465	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 2x M8/4-pin female connectors for two illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 80 cm, M8 cables 20 cm)
	Multi headed cable Type E4 Split cable for illumination Article no.: 11701466	Split cable M12/12-pin female connector to 1x M8/3-pin male connector (to power the camera and I/Os, enable hardware trigger via input) and 4x M8/4-pin female connectors for four illuminations The I/O voltage is directly distributed to the illuminations. Protection class IP65/IP67 Length 100 cm (M12/12-pin cable 20 cm, M8 cables 80 cm)

Illumination

	FFPR-i100-W Article no.: 11086540	flashable LED dark field illumination white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 100 mm
	FLDL-i150x15-W Article no.: 11086539	flashable LED bar light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 158 mm × 17 mm × 20 mm housing
	FLDL-TP-Si200x100-W Article no.: 11086537	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 116 mm × 228 mm × 23,5 mm housing
	FLDL-TP-Si36-W Article no.: 11086536	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 47 mm × 47 mm × 15 mm housing
	FLDL-TP-Si85x77-W Article no.: 11086538	flashable LED back light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 95 mm × 95 mm × 15 mm housing
	FLDM-i100-W Article no.: 11086541	flashable LED dome light white 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 130 mm
	FLDR-i90B-IR24 Article no.: 11090900	flashable LED ring light IR 875 nm 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLDR-i90B-SR24 Article no.: 11154321	flashable LED ring light red (626 nm) 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLDR-i90B-W Article no.: 11085869	flashable LED ring light white 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m diameter: 94 mm
	FLFL-Si60-IR24 Article no.: 11095910	flashable LED back light NIR diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 1 m dimensions: 94 mm × 94 mm × 10 mm housing
	ZVI-FLDL-i86x15-W Article no.: 11197768	flashable LED bar light white diffuse 24 V voltage-driven (equipped with integrated pre-resistor) cable length: 0,3 m dimensions: 18 mm × 95 mm × 20 mm housing
	ZVI-LED Spot5WFL-B/SPS-220 Article no.: 11175036	LED spot light blue 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-Adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-IR850/SPS-220 Article no.: 11175035	LED spot light infrared 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-Adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-R/SPS-220 Article no.: 11175034	LED spot light red 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-adapter cable (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-LED Spot5WFL-W/SPS-220 Article no.: 11175031	LED spot light white 19… 30 V cable length: 0,15 m diameter: 34 mm adjustable glass optics for spot or broad light integrated flash controller and potentiometer (brightness and exposure time) direct connection to M12/12-pin connector thanks to T-adapter cable (ZVI-LUMIMAX T1-adapter cable illumination (11175008)) maximum exposure time 220 µs (maximum frequency 35 Hz)
	ZVI-ARCUSM_24VDC_WEIß_120° ARCUS-M white 24VDC with M8 connector Article no.: 11130183	flashable LED dark field illumination white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 120 mm
	ZVI-HILIGHT120_24VDC_WEIß HI-LIGHT-120 white 24VDC with M8 connector Article no.: 11130182	flashable LED back light white diffuse radiation angle 120° diameter: 94 mm 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 127 mm × 127 mm × 20 mm housing
	ZVI-HILIGHT80_24VDC_WEIß HI-LIGHT-80 white 24VDC with M8 connector Article no.: 11130181	flashable LED back light white diffuse radiation angle 80° diameter: 94 mm 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector dimensions: 87 mm × 87 mm × 20 mm housing
	ZVI-LOGO2_24VDC_ROT617NM_30° LOGO-2 red 617nm 30° 24VDC with M8 connector Article no.: 11130184	flashable LED bar light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 74 mm × 15 mm × 17 mm housing
	ZVI-HELIOS-130_IP65_weiß_80°_24VDC_M8 HELIOS-130 IP65 white 80° 24VDC with M8 connector Article no.: 11701627	flashable LED ring light white radiation angle 80° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 134 mm IP65 protection
	ZVI-RONDOLX_24VDC_IR850NM_120° RONDO-LX IR 850nm 120° 24VDC with M8 connector Article no.: 11130150	flashable LED ring light infrared (850 nm) radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-RONDOLX_24VDC_IR850NM_50° RONDO-LX IR 850nm 50° 24VDC with M8 connector Article no.: 11130176	flashable LED ring light infrared (850 nm) radiation angle 50° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-RONDOLX_24VDC_WEIß_120° RONDO-LX white 120° 24VDC with M8 connector Article no.: 11130179	flashable LED ring light white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) diameter: 101 mm
	ZVI-TOPLIGHT80_24VDC_rot617nm_30° TOPLIGHT80 red 617nm 30° 24VDC Article no.: 11135012	flashable LED incident light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 87 mm × 87 mm × 20 mm housing
	ZVI-TOPLINED1_24VDC_ROT617NM_30° TOP-LINE-D1 red 617nm 30° 24VDC M8 1-canal Article no.: 11130187	flashable LED bar light red (617 nm) radiation angle 30° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing
	ZVI-TOPLINED1_24VDC_SHWEIß_120° TOP-LINE-D1 SH white 120° 24VDC M8 1-canal Article no.: 11130186	flashable LED bar light SH white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing
	ZVI-TOPLINED1_24VDC_WEIß_120° TOP-LINE-D1 white 120° 24VDC M8 1-canal Article no.: 11130185	flashable LED bar light white radiation angle 120° 24 V voltage-driven (equipped with integrated pre-resistor) M8/4-pin connector (cable has to be ordered separately) dimensions: 78 mm × 25 mm × 23 mm housing